Jump to content

Belloc

Member
  • Content Count

    95
  • Joined

  • Last visited

Everything posted by Belloc

  1. Selling the same Tromix 308 that was purchased here: http://forum.saiga-12.com/index.php?/topic/12391-wts-tromix-saiga-308/&do=findComment&comment=101008 But has gone through a few changes and upgrades since then. Complete package including ACOG TA-11B and GDI qd mount, Elzetta light & qd light mount with EMA side mounting bipod w/ 7 polymer mags and 2 Csspecs 20 round mags. Perhaps 200 rounds fired since the purchase for a total of no more than 300 rounds give or take a couple of mags. (Probably closer to between 200-250) (The bottom photo of reticle of the TA11B is fr
  2. Update. According to TWS in this video (at the 4:14 mark), the handguard unfortunately will "not yet" (not sure what that means) work with 308 Saigas.
  3. I could be wrong, but based on this image from the Texas Weapons Systems homepage it looks to me like it should fit the Saiga 308 barrel diameter.
  4. From Texas Weapons Systems. http://www.texasweaponsystems.com/category-s/1880.htm
  5. I went with the DPH Arms Tri-Rail and could not be happier with the choice.
  6. Not without a qualified gunsmith probably spending some serious hours on the project. Here's a pic I found doing a google search.
  7. Does anyone know anything about this rail system from DPH Arms? http://forum.saiga-12.com/index.php?/topic/93734-dph-arms-saiga-rifle-tri-rails-9999/
  8. Nicely done! Good to learn that just like with the Vepr, the heat shield must be modified to fit on a 308 Saiga. Thanks for the info. However that has me now leaning towards going with the standard Magpul MOE AK handguard.
  9. Since the Saiga barrel is tapered, and the front barrel clamps fits, have you considered drilling two holes in the bottom of the metal heat shield a few inches closer to the front clamp?
  10. Anyone know if Zenitico handguards will fit on a 308 Saiga? http://russianoptics.net/zenit.html
  11. So I just telephoned and was told that you do not take orders over the phone for this item and to instead "fill out the comments section" when I place the order online.
  12. Not having anything much beyond what's in the toolbox, what is needed to best grind away enough metal to get it to fit? Thanks.
  13. Perhaps a different rear sight block? Clearly from the pics of the milled and stamped gas tube lever there is a difference in width. This is as far down as the rail will go. The wider than stamped rear sight block just stops it cold from going any further.
  14. Sad to report the Titan AK dustcover rail will not fit either on a milled SLR-95 or a Mak-90. The rear sight block is simply too wide. This photos of the gas tube release lever shows the difference.
  15. Ok, I think I am following now, and this video was helpful. So there are differences between the front hand guard hardware, but no differences with the over the dust cover rail seen here: Correct?
  16. Ok, however I don't know what you mean exactly by "hardware". Could you please explain? I ordered a Titan rail for a Mak-90 from CSS because they have them in stock at the moment, but then only later noticed the two options on the Chaos website, which the CSS website does not have. Thanks for the help.
  17. I have read that that since Veprs have a larger diameter rear sight block, the Titan dust cover rail will not fit them. I noticed on the Chaos webpage there is an option for Saigas and for AK47s. http://www.chaosus.com/cgi/commerce.cgi?preadd=action&key=AK_QUAD_RAIL_REAR What is the difference between the two? And any idea if Titan rear rail will work on a Mak-90, or does it also have a larger diameter rear sight block? Thanks.
  18. Any idea when these will be available again? Thanks.
  19. 7 of these are new and have never been loaded, 2 have been loaded but never fired, and 1 I am not sure about. $375 shipped USPS Priority w/ tracking number. Thanks. All mags sold! Thanks.
  20. $150 shipped each and can do discreet pp. Thanks. Edit update: The B5 stocks have been sold. And one folding mechanism sold, leaving one Ace folding mechanims and PWS buffer tube. Items sold. Thanks.
  21. An integrated AK folding stock set-up. -Ace push-button folding mechanism -Vltor tube with watertight storage compartment -Stormwerkz universal adapter $115 shipped. Sold. Thanks.
  22. Well, 5 days and still no reply from Ace. In any case I simply put a strip of grip tape between the two attachment screws to remove the slight play that was there when the mechanism was closed. It has worked well so far.
  23. I'll probably try that next, just thought I would ask here first since Ace is notoriously known for not getting back in touch with people.
  24. Thanks for the replies, and that might not be a pic of an Ace mechanism, (my bad if that is the case) but it is still a copy of the old Ace style. The pic below is in fact the old Ace push-button folding mechanism. I know this for a fact because I have two that I purchased from Ace many years ago. But I recently noticed the change in design and was wondering if anyone knew the reason for the change.
×
×
  • Create New...