Jump to content

mrwiggles2004

Member
  • Content Count

    27
  • Joined

  • Last visited

Community Reputation

15 Neutral

About mrwiggles2004

  • Rank
    Member
  1. It looks like there is an awful lot of space still between your ring halves. Have you followed the proper torque sequence when installing the rings? It looks like either the rings are not all the way tight or you completely tightened one sid of the rings all the way and then did the other side leaving a gap.
  2. Looks nice! What sling are you using BTW? Ultimate Arms Gear multi point. Can convert between single point and a two point. 6" and 2" rails added, Magpul AFG2 installed, robbed the Surefire off my 1911 till I get a Streamlight for this rifle. I like it. The AFG breaks up the weird curve of the HG nicely. Random question, but do you happen to know how much your phoenix tech stock weighs? Thanks! It's an easy mod, and there is a big chunk of metal right there so you even shave a hair of weight.
  3. Looks nice! What sling are you using BTW?
  4. Thanks! I've got grip tape on my 1911's and i like the way it feels. Didn't think about that for this, but that probably wouldn't be a bad idea. Good job on the cutouts! Good advice going on here. With my next attempt I will indeed use a smaller solder tip to achieve a more uniform and sandpaper like texture. To be honest this is the first time I have stippled anything, and all I had was an old worn out tip that I didn't mind getting plastic all over. Good learning experience either way. In the picture I don't have my flashlight mounted, but it is usually sporting a streamlight poly
  5. Thanks! I'm attached to her, and she groups well with the RSA trigger. Definitely my favorite conversion.
  6. Good job on the cutouts! Good advice going on here. With my next attempt I will indeed use a smaller solder tip to achieve a more uniform and sandpaper like texture. To be honest this is the first time I have stippled anything, and all I had was an old worn out tip that I didn't mind getting plastic all over. Good learning experience either way. In the picture I don't have my flashlight mounted, but it is usually sporting a streamlight polytac in 1" rings on the forward rail. I thought about swapping one of the direct mount M lok scout mounts for my light to save some weight. Bolt it
  7. I used the factory trigger guard and drilled a hole for a screw and nut. Red loctited it all down and haven't had any problems. I went with the RSA trigger, and as others have mentioned I had the side-to-side play as well. I took some aluminum spacers from HD and cut them to size for either side of the trigger pin.
  8. This is the first one I have done, and the vents aren't the smoothest, but I like the way it turned out.
  9. Factory AK gas tubes have their furniture brackets spot welded on, so they could be moved after grinding the welds and re positioning. After a few mock ups I determined that it wasn't worth the trouble for me because the lower HG and upper HG were almost exactly proportional to their original config just shorter. It is in fact a 16" barreled Saiga .308, and it was bone stock when I got it accept for a Tapco T6 Saiga stock. It looked just like this And then after the conversion. I did the conversion and threaded the barrel at the same time.
  10. Thanks for the feedback. I may stipple the whole thing in some fashion, or like you said just do the whole back. All in all I think the vents, and cutting the front square to the gas block made the most positive visual difference. I think your right on the weight aspect. I am not going to get anymore off of the HG without compromising rigidity. Next step is cutting the barrel, pinning FH to 16" and pushing the FSB back. The goal is 6.5lbs.
  11. I did something similar on my .308, and it consisted of the following: -PSL Handguard -Dinzag HG Retainer I mounted the HG Retainer directly behind the gas block, and trimmed the PSL wood to fit. It's not that hard really if you have some patience, and basic woodworking skills. The upper HG is a standard AK gas tube and the PSL Upper shaved to match the lower.
  12. My wife says it looks like barnacles, LOL. I agree. I definitely wouldn't stipple a Glock frame or anything, but I have a pile of these handguards so what the hell.
  13. In my quest to shave as much weight as possible off of my Saiga .223 I have come to the conclusion that the factory handguard is lightest inclusive system at the moment. That doesn't change the fact that they have a look that only a mother could love... So having a few laying around I went ahead and hacked and stippled one to see if I could make it any better. I think the results turned out pretty decent. One thing I did that I have not seen anyone attempt is to stipple some parts for a better purchase. despite being a bit cliche' this particular application seems to work well. What a
  14. I recently modded 10 M85 mags for my saiga .223 and they have been 100% so far. Mine fit like a glove as well with similar mods as the OP. I did some rapid fire with them just to test but i generally take my time when I shoot so they haven't really been "torture tested". After the first mod the other 9 went really quickly with a dremel. For the price I paid I don't think there is a better mag option for the S223 as long as they continue to function and the prices stay low. Only negative is they are heavy as hell and don't like mag pouches, but overall I'm extremely happy with them.
×
×
  • Create New...