Stuart2

Yes 2 pins that go from one side to the other side in must cases just like any other AK rifle, see post above for exception to the case, dont you have a rifle? look on the FSB and GB, you push the pins out and press the part out. Yes I do have a saiga rifle 762x39 Have read your comments & yes I do understand now. thanks

Are you saying that all saiga rifles have pins in the front sight? thanks

Hi Guys, Would you know how to take off the front sight, so I can decrease the barrel length to 16 What tools would I need? thanks Stu

The porting looks great. Maybe I will give it a go at some stage? Stu

Hi, when you say that you measured out 8mm for the first hole then 32mm to the last hole. From what point did you measure the 32mm? was it from the 8mm first hole or from the start of the tube? thanks Stu

I'm searching around the internet to see if there is anything that I can put on the gas block to control flow, adjustable valve. What I have studied so far is that the control of the gas must be at the gas block not the tube as the pressure is greatest at the top of the pistion ( gas block ) that's if you are wanting to control the piston speed ( pressure ) Something like a bike tyre valve but adjustable with the gas flow. See picture Stu

Hi there, Have you a photo of the gas port that you ported? a close up photo. Could not find anything about how to port the gas tube on this website. Can you say what drill size you used? maybe it was 1.5mm or? any info would help thanks Stu

Hi Guys, Was at the range two weeks ago, well I would be there today but it's raining in Auckland. Shit. I was trying reloads & found that the reduction in powder loads, that the bullet case when ejected was damaged less than with higher powder loads. 1 example 24 grains ADI 2206 powder there was near no damage but when using 26 grains it was clearly damaged. 2 With the 24 grains or less that the bullet case was ejected 1 to 2 feet beside me. Instead of the case going 20 to 30 feet & I can not find it. Question, I need 26 grains powder to be accurate at 100 yards. Can

Hi PvtPyle, thanks for your reply. I live in Auckland New Zealand. The main issue is that you will consider sending overseas. I need a permit from the NZ police before I can order these magazines. It's great that you have made these mags. thanks Stuart

Hi, do you know if the export overseas? I looked at there FAQ but am still not sure. I could email them but on this forum they has asked us not to email. thanks Stu

thanks guys

Hi Guys, would this ammo be box primed or bird? I'm thinking about using the cases for reloading when I have shot them. Highland 123gr soft point. Only if boxed primed would I reload using these cases. thanks Stu

What's stockers? thanks Stu

Hi, I need to catch up on the saiga 308 as at this point I have not purchased one. This maybe a stupid question? Is there anyother type of magazine that can fit this rifle? example M76 or Romac 3 magazine?. I have purchased at this time the 762x39 & 12ga saiga but thinking of more punch. thanks any help would be great Stu

Hi, would it be worth reloading slugs for the 12ga shotgun. Is it hard to reload? 12ga slugs Would it be cheaper than buying? thanks Stuart

Hi guys, 1 Can you say what's the best military ammo for best groups at 100 yards? Norinco, Wolf, Simpson ect This is using the Saiga 762 by 39 2 If reloading, what type of bullet weight would you use? 3 Reloading for this rifle, would it be worth the problem with the ejection that may damage the casing. Plus runing after this casing or trying to find it maybe hard. thanks Stu

Hi guys, spank2798 all saigas can fit this stock, with all ak47 stocks that are for the stamped receiver. My shotgun will take a photo to show you. Has the Maadi type stock. Yes the saiga has to be put back to the original state, from Saiga to AK trigger forward ect. We have a local person that does hundreds of conversions. Hi dinzag will think about it, as to be economical for me I would have to order 3 stocks minimum, due to shipment cost. Stu Hi Guys, here is a photo of the 762 by 39 with the stock we are talking about. Stu

Hi Guys, globaltrades.com will not send overseas. That's life I guess. Stu

Hi Guys, have emailed globaltrades.com & will see if they will sell outside America, as I'm from New Zealand. Cheaper than dirt will not sell outside America. If there are anymore places that sell these stocks please let me know. I will ask each place if they will sell outside American then I will order 3 stocks. My intent is to mod the saiga 762 by 39 with this stock. Trigger forward ect. Stu

Hi guys, looking for this stock as per photo. Would you know the name that they call this stock? & where to purchase? Is this the name? Ivan Kolev thumbhole buttstock thank you Stu

Hi Guy What I'm trying to workout, is the reasons why you are changing the trigger, hammer ect because the law within american states that you must follow the 922r compliance ? Do you agree with this statement below You need to change the parts to ( AK G2 Single Hook Trigger Group ) to make this saiga rifle work? thanks Stuart

Hi Guys With this conversion to put the trigger forward, Do we need to purchase a special hammer, disconnector & trigger for this saiga? or Can I use the same Trigger, Hammer & Disconnector????? thanks Stu needs help

So you are saying that not even the saiga with thumbhole stock is not imported? example this photo is the one thanks Stu P.S When you get a gunsmith involved, the price is very very high

Hi Guys Would like to know where to purchase the Saiga M Series Rifle, 7.62 by 39 or .308 It's the one with the Thumb Hole Stock. thanks Guys Here is an example:

Hi guys In this forum we have had photos of trigger conversions. Can anyone point me in the right direction? I'm thinking of this trigger forward conversion, like the normal AK47 ect. 1 Can I do it myself or would it be best to leave this to a gunsmith? 2 Do I need a conversion kit? & wher to purchase them from? thank you Stuart