russm4a3
Contributor-
Content Count
69 -
Joined
-
Last visited
Community Reputation
5 NeutralAbout russm4a3
-
Rank
Member
-
AR build
russm4a3 replied to kukurilynch's topic in General Discussion - Any topic is welcome here!!!
80% are not hard to do if you have a drill press,a router, and a 80% jig but it does take time. Most of the sites selling the lowers sell the tooling necessary to complete them. I would get one of the 80s that have the rear of the receiver milled out a bit already, saves time. -
They are done tweaking the mags and were happy with the results from their test fire. They should start shipping next week.
-
Kevin Phillips posted in Vepr 12 Club Kevin Phillips 11:42am Dec 4 success Kevin Phillips posted in Vepr 12 Club
-
You might not have to take the magwell off to get the mag release back in. I just couldnt figure out how to do it otherwise. Has anyone else switched theirs out? Did you have to take the magwell off to get the release in?
-
So I just barely finished installing the same mag release from CSS. It was kind of a pain in the ass for me. In my case I ended up removing the mag well in order to get the mag release and spring back in. I just couldn't manipulate it with the mag well in place. Removing the magwell was a breeze, I just used a flat head screw driver that I dremeled the middle out of to get around the screw that the nut sits on. Once the magwell was off I was able to get the spring and release back in place and used a rivet that I cut to length to install the mag release back in. I made sure it was only long e
-
The Hellion
russm4a3 replied to thebuns1's topic in General Discussion - Any topic is welcome here!!!
So Jealous! I have been eyeing either the Hellion or the Vakra for a while now. I have been noticing their turn around times keep extending everytime I log into their site. I need to jump on one soon before it turns into 12 weeks, I've just been having a hard time deciding between the 2 blades. They are far from a machete that are mass produced and sold for 10 or 20 bucks, they are works of art that are functional as well. Congratulations on your purchase. I look forward to reading your chopping/cutting reviews! -
Did you fabricate the lower rail for your FB hand guard? I just got mine back from them and it did not have a lower rail? So I was supposed to get a comp put on but there was some confusion and mine shipped without it being on. I can either send it back in to get it on or receive a credit. Is the comp a must have in your opinion? How's the reliablity with it on there? I shot mine yesterday only 120 rounds or so but I did not have a single feeding issue with the gun or the 10 round mag.
-
Is the polymer stock supplied the one pictured on the VEPR on your website? (Not a Tapco?)
-
Gun Safe lighting recommendations?
russm4a3 replied to Spacehog's topic in General Discussion - Any topic is welcome here!!!
Very clean and well organized safe! I bought the same light set at a gun show earlier this year. Are you using the door pressure switch with your kit? I tried using some 3M tape to hold it in place but after a week or so the switch gets pushed back and the batteries die. I probably need to screw the switch into the door but I do not like the idea of drilling into my safe. You heard correctly, always buy more safe than what you think you'll need. My first safe was a 30x27 and I filled it in 2 years. I later purchased a second larger safe and it too is now full. Every time I buy a new gun so -
Vepr 12 Russian Shotgun Pre Order Atlantic Firearms.com
russm4a3 replied to Atlantic Firearms.com's topic in Vepr-12
Email sent concerning the second order, thank you! -
Vepr 12 Russian Shotgun Pre Order Atlantic Firearms.com
russm4a3 replied to Atlantic Firearms.com's topic in Vepr-12
Preorder for 1 placed, if i order a second would you combine shipping? -
Ordered mine!! Happy early birthday to me!
-
I'm liking that stock on there, looks really good!
-
Saiga Shirts (pre order re open for weekend!)
russm4a3 replied to Juggernaut's topic in Misc - Everything Else (WTS / WTT)
I'd buy one with just an image