Jump to content

clay1003

Member
  • Content Count

    29
  • Joined

  • Last visited

Community Reputation

0 Neutral

About clay1003

  • Rank
    Member
  1. Ironwood Designs, Black Walnut stained Red-Red Mahogany
  2. Friends, I bought a new SGL41 and tried it out for the first time 2 days ago. With the factory 4 round mag it jammed quite a bit and I don't know if it was the gun or the shells. I'm using my own reloads of Fiocchi 3" hulls. Also, and equally as disappointing, I loaded up my new Surefire 15 rounder with these same reloads and couldn't even get the mag into the receiver.. regardless of how many rounds I had in the mag! It seems their too long!? WTF. So, it's either the gun is jamming or it the Fiocchi hulls. Anyone have a similar experience? How about the Surefire 15er not fitting?
  3. Sorry for the duplicate post. Please see my other post of the same topic. Thanks
  4. Bingo! It worked. Thanks much! Clay
  5. Thanks Volkov.. I understand what you mean and I've found some video's on youtube showing whjat your describing. Problem is, the Arsenal top hand-guard is so tightly pressed between the front/rear retaining brackets of the gas tube that it seems as if it was "pressed" on and cannot be removed. I'll try anyway. I sent an inquiry to Arsenal and asked if the top hand-guard is replaceable. If they say no, I'll be bummed. I'll post what I find so others will also know about the Saiga/Arsenal conversion. Clay
  6. Thanks. It doesn't have a bolt.. but I just got it off. I guess my biggest question is if the poly furniture on this Arsenal SGL41 (converted Saiga 410)can be replaced with wood. I can't see how I could get the top handguard off of the front/rear retaining clips. It looks like it's all press on together. Arrrrrh.
  7. Friends, I just purchased an Arsenal SLG41 and am trying to remove the hand-guard. I thought I knew what I was doing but I'm having difficulty and need some advice. I've raised the little lever to the right of the rear site and am pulling the upper hand-guard towards the receiver while trying to lift up.. but it only moves a little and I'm afraid to break or scratch something. Any advice? Thanks much, Claypij
  8. Sorry for the lack of clarity. On one side of the surefire mag, at the top and on one side (not both sides) I put some dabs of epoxy and smeared it about. Capice? Clay
  9. Thank you Gentlemen. Yes, it's a Surefire that's been modified to accommodate steel Barnal shells and I epoxied one top side to reduce the wobble. Just put some on, let it cure and sand down until it fits to your liking.
  10. ... with the possible exception of a FSB. Thanks for Danzig for his compliance components and Battlerifle for his red oak furniture!. I did some tweaking and everything went well. I like it. Clay
  11. Friends, I have 2 Surefire 10 round magazines for the Saiga 410 that I won't be needing. They've never been used, 1 is still in the sealed poly bag and the other has been modified to accommodate the metal hulled Russian shells. Mississippi Arms has them on sale at $41.55 ea. plus $7 S & H. You can have them both for $70 + actual postage. First come first serve. Let me know. Thanks, Clay
  12. Nothing comes up except your response mentioning dental floss. Can you be more specific? Thanks, Clay
  13. Friends.. I'm certain this topic has been covered numerous times. Could someone point me to the info concerning re-installation of the BHO for my saiga .410? I'm down to the the wire and so far it's been smoothe sailing.. with the exception of the BHO. All the instructions I've found don't mention it. Is it eliminated by necessity? Or can I re-install it? How? Spring? HELP Thanks, Clay
  14. Saiga 410 Friends, After almost 2 years I'm finally getting to my conversion. I'm at the point of searching for a sling and most importantly... the sling rings. I have the rings that came with my gun and imagine I can reuse them. But they are so narrow (3/4" wide). It seems a sling with a snap clip on each end is needed? Any assistance is appreciated. Thanks, Clay
×
×
  • Create New...