Search the Community
Showing results for tags 'modification'.
Found 4 results
Automatikjack posted a topic in Conversions and Modifications for the Saiga firearmsHello all, I have a few questions regarding the parts for conversions and modification of some magazines for LRBHO. First: Looking at the conversion kits at California Shooters Supply at my options for converting my newly purchased IZ-433, and I have some concerns about the trigger guard. I don't really see any information showing if either of the trigger guard options will interfere with the tab up front for the mag well. I would imagine the answer is no, but I have no way to make a real mock up other than to use the pins in the receiver for an approximate of where the trigger guard will end up. The trapezoidal one (Tromix DIY) looks neat and seems to offer more space for gloved fingers, but would get pretty close to my magwell and reduce the overall space for the mag release tab. Here is the proposed kit. Does anyone see any problems/compatibility issues or am I over analyzing this? Here's the second project: (Note: I am aware that there are magwell magazines, but I got 4 new mags for just under the price of two 10 rounders) I got a killer deal on some SGM 12 rounders, so I decided I'd sacrifice one in the name of being poor (ironic right?) and see if I can get it to work with my gun like some of the other people in the forums have done. With a dremel/file and some eyeballing it locks in perfectly with very little side play and no wiggling front to back. It basically sits in the same position as my factory mag. Here's the mags side by side, the angling was a little tricky and ended up involving lots of time with my file. After enjoying a brief victory, I noticed that these SGM magazines do not have a BHO. So while I made myself a little notch for the BHO lever, I need to figure out a way to get the SGM followers to engage the BHO lever or just replace them outright. Each option has its problems. If I were to keep the stock follower, I would have to add a bho tab that would need to physically extend past the top of the follower about 1/4 inch to properly engage the BHO. Some late night garage experiments were promising with small pieces of steel picture hanger hooks, but the looseness of the follower caused the thin piece of steel to move forward and not properly engage the BHO. I have found several other donor pieces of metal that could possibly serve as tabs to engage the BHO latch listed below: A salvaged PSU heatsink, a CPU heatsink, a bracket for a recessed light and a thin piece of spring steel that is just the right width of the follower and with the perfect curve and pre punched holes that would work for rivets. I have three options for mounting it onto the follower, one being to glue it, which would work pretty good if I decide to use more polymer, or maybe alright for metal, but ideally I'd either use the small slit I made in the picture below to fold a piece of metal inside and grip the plastic. (it worked very well for the picture hanger, until I snapped it after adjusting the length multiple times.) The last that I am thinking about is using rivets to secure it, and hoping that the channel will provide enough clearance and hopefully that the rest of the mag will not interfere with the attached piece. The last and easiest would be to just find followers with BHO and drop them in, which I have (so far) had no luck in locating. I noticed that the sgm followers are (as claimed) made from the original design, but have a few changes that vary it from the original. Pleasingly enough the follower from the factory 4 fits right in....except for these two little feet which I am guessing serve as anti tilt. As much as I would love to take the feet off or bend them in to test it. I don't want to risk messing a more expensive/rarer mag to make the common one operational. You can see what I am talking about below. So to wrap things up, while I am scratching my head trying to make heads or tails, has anyone seen or know of a place that sells followers with bho or does anyone have any suggestions that might help with this dilemma?
Hello all, I am looking to get a mka 1919 xn or br 99 for home defense purposes. I have some ideas as to how I would like to modify/customize it, but would love some ideas and feedback from you guys. Feel free to critique the following and/or offer up the best HD builds you can think of (on or off a budget). My current thinking is as follows: to not go sbs at the moment due to cost and time. Weight isn't a huge factor as I won't be lugging it around all that much outside of the range (hopefully), however it should still be light enough to manipulate and aquire targets quickly. Ability to cycle low power and low brass is no biggy as it will be used with high velocity 00 and #1 buck and perhaps slugs (no kids in the house yet). Reliability and accuracy (within reason this wont be a completion gun) are huge factors, if you don't hit, they don't go down. Will need 922r compliance as reliable high capacity (I'm thinking 8+?) are a must. Mount red dot, mount flashlight/for grip, ???, profit. (And probably a new stock and sling) On a side note I have a decent amount of xp with both ar and ak systems, but this will be my 1st semi-auto shotgun. Thanks for the feedback and opinions!
TheJoe90 posted a topic in Other AK RiflesHowdy yall Problem: Trying to improve cheek weld on Polish Underfolder with red dot. Samson riser doesnt fit... What next? Background: My beautiful Polish AK, utilizing a NoDak receiver and a Primary Arms red dot is amazing! I just would like a better cheek weld for it. I purchased the Samson riser, incredibly excited to use it, and it didn't fit. This weapon is easily my favorite rifle. Solution 1: Identify and purchase a second underfolder stock that will be more compatible with this riser. Determine if new underfolder will fit. Solution 2: Price out a direct replacement for my current stock so that if it were to be damaged beyond use during modification it can be replaced. Solution 3: Return it for a refund, suck it up, and deal. Close: Looking for input from those who have experience, thank you for your time.
sonofliberty posted a topic in Conversions and Modifications for the Saiga firearmsI had an idea today and I wonder if anyone has tried it already. Everyone has seen the shark breaks and such that make a muzzle device such as a break or flash hider double as a sort of pronged bayonet-like weapon. I was wondering if anyone has grinded down the Vortex Flash Eliminator like so: My concern is that it would hinder the flash hiding ability. This would be unacceptable. In addition to grinding down the prongs to form sort of edged teeth prongs (probably sharpened), I was also wanting to grind down the extra thick neck because it seems thicker, and therefore heavier, than necessary. Tell me what you guys think.