Jump to content


Photo
- - - - -

Internal Receiver Block Installation Video


  • Please log in to reply
5 replies to this topic

#1 CarolinaSS

CarolinaSS

    Citizen

  • Business Member
  • PipPipPipPip
  • 1,848 posts
  • Gender:Male
  • Location:South Carolina
  • FFL_Verified
  • 01FFL
  • Licensed Gunsmith
  • Verified Business

  • Company Name:

    Carolina Shooters Supply, Inc.

  • Company Website:
    CarolinaShootersSupply.com
  • Contact Email:

    carolinashooterssupply@yahoo.com

  • Contact Phone:

    (843) 655-7657

Posted 08 July 2010 - 06:21 PM


www.CarolinaShootersSupply.com

Saiga Conversion Parts, Vepr & AK47 Magazines and Accessories
Forum members receive a
10% discount off all parts and accessories.
Enter
CSS in the "Promo Discount Code" box on the shopping cart page.

Office hours: Monday-Friday 9am-3pm Eastern Time.

803-547-0701


#2 bob the gunslinger

bob the gunslinger

    Advanced Member

  • Member
  • PipPip
  • 233 posts
  • Gender:Male
  • Location:tampa,florida

Posted 08 July 2010 - 10:44 PM

http://www.youtube.com/watch?v=apHGSExPmUo


thank`s greg for the great video!

#3 Mercenetti

Mercenetti

    Member

  • Member
  • Pip
  • 18 posts
  • Gender:Male
  • Location:BEALE AFB

Posted 14 September 2010 - 10:05 PM

What if your side holes have been welded?

#4 CarolinaSS

CarolinaSS

    Citizen

  • Business Member
  • PipPipPipPip
  • 1,848 posts
  • Gender:Male
  • Location:South Carolina
  • FFL_Verified
  • 01FFL
  • Licensed Gunsmith
  • Verified Business

  • Company Name:

    Carolina Shooters Supply, Inc.

  • Company Website:
    CarolinaShootersSupply.com
  • Contact Email:

    carolinashooterssupply@yahoo.com

  • Contact Phone:

    (843) 655-7657

Posted 14 September 2010 - 10:18 PM

What if your side holes have been welded?

You can use the top screw and then use the grip nut as the second secure point sitting over the 2 arms.

www.CarolinaShootersSupply.com

Saiga Conversion Parts, Vepr & AK47 Magazines and Accessories
Forum members receive a
10% discount off all parts and accessories.
Enter
CSS in the "Promo Discount Code" box on the shopping cart page.

Office hours: Monday-Friday 9am-3pm Eastern Time.

803-547-0701


#5 ViperHummel

ViperHummel

    Member

  • Contributor
  • Pip
  • 57 posts
  • Gender:Male

Posted 07 August 2011 - 08:14 AM

I ran into the issue where the side screw holes don't line up. I widened one a little bit on the receiver, but it wasn't good enough. Any suggestions? Maybe a style of bit or something to open the hole in an oblong fashion?

#6 CarolinaSS

CarolinaSS

    Citizen

  • Business Member
  • PipPipPipPip
  • 1,848 posts
  • Gender:Male
  • Location:South Carolina
  • FFL_Verified
  • 01FFL
  • Licensed Gunsmith
  • Verified Business

  • Company Name:

    Carolina Shooters Supply, Inc.

  • Company Website:
    CarolinaShootersSupply.com
  • Contact Email:

    carolinashooterssupply@yahoo.com

  • Contact Phone:

    (843) 655-7657

Posted 07 August 2011 - 08:18 AM

I ran into the issue where the side screw holes don't line up. I widened one a little bit on the receiver, but it wasn't good enough. Any suggestions? Maybe a style of bit or something to open the hole in an oblong fashion?

If the tang is cut flush it should line up. Set the back of the receiver on a table to verify it sits flush and does not wobble. You can then elongate the receiver hole with a file if they still do not line up.

www.CarolinaShootersSupply.com

Saiga Conversion Parts, Vepr & AK47 Magazines and Accessories
Forum members receive a
10% discount off all parts and accessories.
Enter
CSS in the "Promo Discount Code" box on the shopping cart page.

Office hours: Monday-Friday 9am-3pm Eastern Time.

803-547-0701





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users