lokmeup 30 Posted April 21, 2012 Report Share Posted April 21, 2012 (edited) MAGWELL SMOOTHING: The magwell has some residual rough areas from the injection molding process. Sanding these down helps improve smooth mag insertion and removal. The main area to be sanded smooth is at the inside front of the magwell. The inside rear of the magwell can also be sanded, but mine did not require any. However, do not sand the inside sides of the magwell, as these help stabilize the magazine while in the firearm. RUSSIAN MAGAZINE FITTING: The 8 round magazines from Legion USA Inc worked perfectly without any fitting, but the 8 rounders I received from RusMilitary would not lock into the firearm. On these magazines the bump on the rear of the magazine needed to be filed down until lockup occurred. File a little bit at a time and check frequently to obtain lockup and maintain a tight fit. AGP MAGAZINE MODIFICATION: I was surprised how little modification is need to obtain great lockup with AGP rock-and-lock magazines. If I would have known this first, I might not even have purchased any Izzy 8 rounders. There are several steps fitting AGP mags. 1st step - Front Lug: Mill or file the front lug off of the magazine. I found that using a Magnetic Polycast Protractor allowed consistent results. I simply set the magazine in the mill with the protractor resting up against the second screw bump at 25* and milled down the front lug until the thickness of the magazine lip was 3mm thick. 2nd step - First Screw: Mill or file down the first screw bump to the exact height of the screw head. This time I set the magazine in the mill with the protractor resting up against the second screw bump at 16* and milled down the first screw bump until the screw head. After this step the magazine should fit perfectly in the magwell. The only other thing to do is deal with the LRBHO, because at this point your bolt carrier will be locked back as a result of hitting the top of the AGP magazine. 3rd step - Release Bolt Carrier: Remove necessary material from the top of the magazine with a Exacto knife to allow the LRBHO to release the bolt carrier when the AGP magazine is inserted into the magazine. Insert the magazine into the firearm and remove only what is necessary. 4th step - LRBHO: Design and implement some way to activate the LRBHO. I spent 5 minutes with scissors, sheet metal, and double stick tape to make the temporary fix seen in the pictures. This was just a temporary fix, and I do not recommend using such thin material or double stick tape. Do what you think is best. Edited April 21, 2012 by lokmeup 1 Quote Link to post Share on other sites
doodi1 23 Posted April 21, 2012 Report Share Posted April 21, 2012 Great write up. This should be made into a sticky. 1 Quote Link to post Share on other sites
madmax4x4 68 Posted May 19, 2012 Report Share Posted May 19, 2012 Great write up. This should be made into a sticky. +1 Quote Link to post Share on other sites
towerofpower93 22 Posted May 20, 2012 Report Share Posted May 20, 2012 Tag...and agree with the sticky recommendation. Quote Link to post Share on other sites
Kdog45ak 18 Posted August 18, 2012 Report Share Posted August 18, 2012 (edited) Just modded one minus the LRBHO trigger. Mine is functional but still gets hung up a bit on insert. I think it could be the ribs on the sides near the top. Thanks for the guide, saved me $150. Edited August 18, 2012 by Kdog45ak Quote Link to post Share on other sites
S12KS-K 40 Posted November 23, 2012 Report Share Posted November 23, 2012 Can this be done with the Izhmash 5 rounders? SGM? Pro-mag? I don't have my s12 030 yet. I will next week. Quote Link to post Share on other sites
lokmeup 30 Posted November 23, 2012 Author Report Share Posted November 23, 2012 Sure. Quote Link to post Share on other sites
Ashur 0 Posted April 18, 2013 Report Share Posted April 18, 2013 (edited) Tried modifying a 12 round SGM magazine I picked up today using the information I found in the forums. Couldn't find step by step instructions for the SGM mag mod for iz-433 so I just muddled my way through with what I could find. This post helped out a great deal so I'm gonna add a little to it. First I cut off the front lug with a utility knife (all the posts I've seen seem to agree on this step). Then I filed down the front lip of the magazine where the lug was until it was close to flush with the rest of the magazine body (many of the posts mentioned straightening the front of the magazine, but did not go into specifics) The magazine fits perfectly. There is no wobble and seems to load fine. I've cycled several rounds through the magazine and have had no problems with it yet. Next step is to get the LRBHO working with this magazine and test it out on the range. Edited April 18, 2013 by Ashur Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.