lewie212

I first started off with a small one I had laying around in my tool box, after breaking a few blades i went a bout a much larger one from ACE. I bought the rigid one because it was the biggest one they had. It would up rubbing on the front sight block and that was as far as I could cut back. it seems to work just great though.

well here she is, still needs paint.

I cut down the fsb in attempt to cut the barrel. With the cutter i used that was the most it would allow me to remove. Can anyone tell me if that is enough material removed to thread and install a tromix shark brake. All help is greatly appreciated.

Will this system work with your titan top rail? And if so, will the HK style sights work on the 7.62x39? Or are they mainly for shotgun app? I ordered the titan rail to replace the exteneded quad i have on my s 12. I do not think that the titan rail is compatible for the 7.62.

Just ordered one as well as a titan top rail. I was wondering if you had an eta for the titan.

If I miss out on the first run of these I will most likely cry my self to sleep every night till I can get one.

Cameron, can you tell me when the pre-order section will be available on your web-page?

I would love to pre order one.MARK ME DOWN! Its going to look awesome next to my s12 xtended quad!

Is there any way you could tell me what is done to beef up the dust cover? I always was told that they were unstable for mounting but when all the big names are doing it, it makes me wonder how. I would like to attempt this to my 7.62 in the near future. my s-12 already has a chaos rail with hk style sights. Thanks-Dan Any gunsmith should be able to do it. The word "Smith", by definition is "worker of metal".

Thanks guys I appreciate all the help

How much material did you have to remove?

tapco with a bullet guide from css....http://store.carolinashooterssupply.com/servlet/-strse-82/TAPCO-AK47-AK-30/Detail?sfs=25dc10e1 it says you have to remove a small ammount of material from the magazine catch.

When you guys file down the mag release do you remove it to do so? or just file it where it is? Just installed a bullet guide and i am trying to figure out the easiest way to fit my mags. Thanks to all.

I am about to install a bullet guide on my 7.62. I was wondering if i filed down the mag release instead of the actual magazine if my factory 10 round mag would still function properly or if i should just fit each mag to the rifle individually. All opinions are welcome and greatly appreciated. Thanks-Dan

his cycles low brass just fine. it even cycles wally world Winchester value pack most of the time.

my cousins 24 inch only has two ports and it cycles great

Id say if you want it done right send it to pauly or cobra I M O.

I would love to preorder the 7.62 quad stacks.

Pauly...ur da man. +100

Thanks for the info.

What is the easiest way to check my local gun laws? I'm from indiana if that helps. Thanks again.

I have an Ace internal receiver block coupled with a Tromix stock. I was wondering what all you guys think is the best folding mechanism to add and how well they hold up. All info is greatly appreciated.

any word on the micro dot? I am interested in purchasing one for my chaos rail and sights. The Primary Arms Microdot holds up well. I put about 200+ rounds through my S12 using it without any problems. I actually ordered their new Micro Green Dot, which is smaller, and I'll let you know how well it holds up. I also had the Tasco RedDot on there, which is a walmart brand reflex sight, and that held up well also. Though experiences with people and the Tasco varies, good and bad, I didn't have any complaints except that the sight picture was higher than preferred, which is why it w

You make a valid point there! Think about that one for a minute.... Do you REALLY want a woman to need a tampon NOW and have the damned thing jam? The devil would quake in fear at what would happen next!

Use it as a tampon dispenser