randyf 35 Posted January 4, 2012 Report Share Posted January 4, 2012 I think CSS does sell the covers +1 on cutting that thing outta there. I can only find dust covers for rifles at CSS Quote Link to post Share on other sites
The_Caged_Bird 474 Posted January 4, 2012 Report Share Posted January 4, 2012 Aren't they the same? I figured they were... Quote Link to post Share on other sites
RED333 1,025 Posted January 4, 2012 Report Share Posted January 4, 2012 I think CSS does sell the covers +1 on cutting that thing outta there. I can only find dust covers for rifles at CSS Aren't they the same? I figured they were... No, the S12 cover has a larger cut out for the larger shell. Quote Link to post Share on other sites
vulcan16 971 Posted January 4, 2012 Report Share Posted January 4, 2012 Better be a good friend.G I think I would ask my wife first and have her to hold it while I wack it. That just doesn't sound right. Quote Link to post Share on other sites
The_Caged_Bird 474 Posted January 4, 2012 Report Share Posted January 4, 2012 I think CSS does sell the covers +1 on cutting that thing outta there. I can only find dust covers for rifles at CSS Aren't they the same? I figured they were... No, the S12 cover has a larger cut out for the larger shell. Well, other than that, the rest of the dimensions are the same? If so, then all it takes is a dremel, a cut-off wheel, and a sanding disc to fix that! Quote Link to post Share on other sites
robfromga 39 Posted January 4, 2012 Report Share Posted January 4, 2012 I think CSS does sell the covers +1 on cutting that thing outta there. I can only find dust covers for rifles at CSS Man your right, only rifles. Maybe a email to Greg? He might have a source? I'd rather replace the cover than the stock, unless you hate your stock. Quote Link to post Share on other sites
The_Caged_Bird 474 Posted January 4, 2012 Report Share Posted January 4, 2012 I think CSS does sell the covers +1 on cutting that thing outta there. I can only find dust covers for rifles at CSS Man your right, only rifles. Maybe a email to Greg? He might have a source? I'd rather replace the cover than the stock, unless you hate your stock. Well, it IS a non-conversion stock and, subsequently, will be pretty useless after conversion... Quote Link to post Share on other sites
bwicks 1 Posted January 16, 2012 Author Report Share Posted January 16, 2012 I agree, and I look forward to hearing just exactly what caused this, I will say this though, when I got a crapco stock for my old S-12, the screws that came with it had smaller heads, I didn't use them, I just recycled the old Izhmash screws that were in the original stock. Well that was it, GOB has the instructions down how to get it apart then just put a lot of torque on the screw...put it back togethere and it is working fine (other than the BHO getting stuck every 7 or 8 times I lock it back). Work around on that is just to bump it on the ground and it will release (until I get some of the upgrades that most of you all have). Thanks all! Quote Link to post Share on other sites
The_Caged_Bird 474 Posted January 16, 2012 Report Share Posted January 16, 2012 It's great to know that you've got it where you can take it apart again, that's kind of a big deal. I'd completely remove that screw, there should be at least one more that holds the stock on, probably two, and if that stock is anywhere near as tight fitting into the receiver as the original stock, you'd probably be fine without any screws at all... I'm running a folder, and I've cut the tang off, I'm only running the little allen screws that go into the side of the receiver, I made sure not to install that top one in the rear just because of your predicament. To date, aside from the factory screw-ups, that screws location is the only design flaw that I can find with the S-12... Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.