-
Content Count
37 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout koertli
-
Rank
Member
-
I just did one of mine tonight, it hand cycles well (it wouldn't even hand cycle before), I'll let you know how it goes, thanks for the heads-up. I bought some Surefire 10s to sell and then started hearing/seeing how piss-poor they worked, I've been sitting on a hand-full of them hoping for a fix so I can sell them. I hope they range test the new 15 rounder and the new 12rnd 12ga mag before they ship them, I will never buy one from their first run again, if I buy from them at all. Good luck, should work well!
-
3" Barnaul #4 Buck. Metal Casing Cool. Are you going to be sharing your modification info? If you own a 4rnd Mag that does work with the Steel loads, line it up with the 10 rnd and notice the difference in length of the top feed lip. I think Cobra provided pic's of this in another post. All I did was shave the lip on both side with a hacksaw blade until it mimicked the 4rnd'r. Very Simple really. *******Do so at your own risk********** If you do not feel comfortable doing this on your own, then Cobra is providing a service to do it. I am not. Foll
-
3" Barnaul #4 Buck. Metal Casing Cool. Are you going to be sharing your modification info? If you own a 4rnd Mag that does work with the Steel loads, line it up with the 10 rnd and notice the difference in length of the top feed lip. I think Cobra provided pic's of this in another post. All I did was shave the lip on both side with a hacksaw blade until it mimicked the 4rnd'r. Very Simple really. *******Do so at your own risk********** If you do not feel comfortable doing this on your own, then Cobra is providing a service to do it. I am not.
-
And what should I expect from SureFire if I contacted them? Seriously, I would have expected to have seen them address this issue on their own and contact me. The fix is really easy as far as I am concerned. I just wished they would have verified that the 10rnd mags would not work with the metal rounds before shipping them out. I would not have ordered them.
-
3" Barnaul #4 Buck. Metal Casing
-
Finally got to test my Sure-Fire 10 rnd Mag Mod. I filled the Mag 3 times 1st round- slow shooting with all cartridges firing without incident 2nd round- steady fired with all cartridges firing without incident. 3rd round- Rapid fire with last cartridge failing to load. I will spend more time on looking at the angle that the cartridges rest in the 10 rnd Mag as compared to the 4 rnd mag. I will see if there is anything I can do to mimic. Other than that, the first test was very promising and almost acceptable.
-
OK, I have tried to purchase 10 rnd mags for three years and got screwed by both Andrei and RussMilitary. I was one of the first to line up for the Mississippi Arms mags. I received them and was immediately disappointed to find out that they would not even chamber my Bear Buck #4. I have even tried to sell my Saiga in frustration Today, I took one the new mags and compared it to my 4 rnd 3" mag that does work. What I noticed as I observed what was happening during the chamberring action was that the Miss Arms Mags did not release the back end of the cartridge quick enough to allow
-
OK, I have tried to purchase 10 rnd mags for three years and got screwed by both Andrei and RussMilitary. I was one of the first to line up for the Mississippi Arms mags. I received them and was immediately disappointed to find out that they would not even chamber my Bear Buck #4. I have even tried to sell my Saiga in frustration Today, I took one the new mags and compared it to my 4 rnd 3" mag that does work. What I noticed as I observed what was happening during the chamberring action was that the Miss Arms Mags did not release the back end of the cartridge quick enough to allow