BuDA

My slug gun. New optics came in the mail today!

HERE'S MY LATEST UPGRADE. CHAOS TITAN!!

Hmm.. that's interesting. I have a hammer that was pre-modified from CSS already. But I may grind and polish it down some more then.

After conversion when it still had the stock handguard on it ran real good with an occiasonal FTE on the last round. After I put on the quad rail I started noticing it happen more frequently. Sometimes I can run through a few mags no FTE's at all and sometimes I cant even get through a full 5rd mag without at least 2. I shoot mostly slugs and 00buck from this gun. I have the worst result when using drum mags. I have both a Promag 12 and MD-20 and almost every other shot is an FTE, which is so frustrating I don't een use them at all. Do you think it really has something to do with the hammer?

No greasing of the piston at all but I will admit it is a bit fowled up. I haven't cleaned it in a while, which is why my gas plug got stuck in the first place.

It's a Chaos Extended Quad Rail. I don't know why my situation would be unique though with so many Chaos rail users out there. However I didn't have the same issue with the stock handguard setup. I'm probably just in denial cause I like the rail. I will try this weekend with the stock handguard as a baseline to see if the problem persists. Then I will try without the top piece of the Quad rail and see if that helps. If it is the top rail that would majorly suck since I had to dremel off the rear stock sight to install it.

I will take it to the range this weekend without the top rail attached and I will report back. Thanks for the help!

Thanks for clearing that up!! I never noticed it before! Sheesh I thought "how the hell did that hole get there??"

I started noticing that my S12 was producing a lot more FTE's about 4 months ago. I could not for the life of me figure out why all of a sudden it started happening when my gun used to perform like a champ even with the cheap Federal bulk pack stuff. I thought maybe it was an issue with my quad rail because the empty shells would get stuck in between the ejection port and the top rail so I let it go (mind you I never tested it without the top rail after the FTE's started happening). I also thought that it could be a gas port issue but when I checked I have three gas ports and they were all cle

5762. Thanks!

Slug-O, here are instructions on how to adjust the spring tension of the Promag: 1. Remove Hex screw on the front and remove the clear cover by popping the tabs. 2. Remove the cylinder in the middle of the drum and the spring will also pop out. 3. Take a rubber mallet and tap out the follower on the cylinder. 4. You will notice the one small hole in back of the drum where one end of the spring goes and also several holes around the cylinder where the other end of the spring goes to create the tension. 5. To adjust, you just have to place the cylinder in there and rotate it until you get t

Wow, yours is the first post that I have read regarding feeding problems with the Pro-Mag drum. Hopefully this is an isolated instance. Let us know how it shoots. Yeah just my luck. Hopefully it works now. I will let you know!

I got my Promag 12rd drum a couple weeks ago from the e-store. It came with the front mag lip pre-filed AND it would not catch onto the mag release preventing it from locking in. So per the fitting instructions supplied by promag, I filed down the plastic at the rear and was able to finally get it locked in. However, because some of the material was pre-removed from the front catch lip, it also wobbled back and forth. My solution was to apply a small amount of JB Weld to the part of the lip that was filed off and once it set and hardened I took a file and carefully filed it little by little u

Here it is. Finally got my Chaos Extended. It was well worth the wait! Only thing left is my MD-20.

Very nice ad! Even better news is that I'm finally gonna get my rails!! I CAN'T WAIT. YEAH!!

Just for the record, I dont work for TGS. I was searching for the lowest price I could find through Google and I happen to come across TGS as a result. I've purchased mags from them before for my GSG-5PK and I found their prices and service to be excellent. With that being said, I rarely post things here because all the long time members have more experience and contribute far better information and help than anything I could provide myself. Thanks to these forums, I was able to convert and fully customize an S12 by myself using parts that I have purchased primarily from other forum business m

Thanks for the quick review chevymann, I am still anxiously awaiting the arrival of both my drums, the Promag 12 and the MD20. I think that I will be using the Promag 12 more just because it is compact and holds two more than that long ass AGP 10rder I currently keep attached to my S12 at home. Man I cant wait! And yes that $75 price doesn't look too bad but I think for me one 20rd drum is good enough to show off at the range! I already get all kinds of looks dumping out my 10rd!

Here's mine for now. Just waiting on my Chaos Extended rail to add my other goodies...

Hey guys and gals, found a really good price on those Promag 12rd drums if you are interested. $60 is a steal if you ask me. Right now they are backordered. I've ordered stuff from these guys before so I think it's pretty legit. I placed a backorder for a couple myself! They are at TGS.

I was going to do the same thing once I got my extended quad. Have you tried shooting it with this setup yet? what are you using to sight it? a boresight?

I have the Ace AR style folding mechanism, with a CAR commercial spec buffer tube and castle nut. All from Carolina Shooters Supply. The setup works great, nice and tight if you use a castle nut wrench, I don't even need a cheek riser.

thanks for the replies. i guess ill break down and get my receiver welded up and refinished from the pistol grip conversion too while i'm at it!

The rivet closet to the rear of the receiver is also attached to something in addition to the mount. If I remove the rivet, would I need to replace it to hold that piece in place? Sorry I dot have a picture to post what I'm talking about because I'm at work. Also Im doing this myself so I won't be welding anything to cover those holes, I was thinking to just use the nylon plugs.

Hello all, I would like to remove the stock side scope mount on my S12. I will be getting a Chaos Extended Quad setup and I know that I will never have a need for it. Does anyone have a step-by-step guide or any helpful tips on removing that mount?

1ST POST! That's one big ass suppressor! It's pretty cool though, not quite Country For Old Men cool, but cool nonetheless considering it has to be that long to work! My question is was that fired WET or DRY?