my762buzz
Contributor-
Content Count
835 -
Joined
-
Last visited
-
Days Won
2
my762buzz last won the day on July 14 2011
my762buzz had the most liked content!
Community Reputation
141 GoodAbout my762buzz
-
Rank
Executive Member
-
Why Do Newer AK Variants Have Skinnier Barrels ?
my762buzz replied to scattergun10's topic in Saiga 7.62 X 39
A millimeter thick stamped receiver spec has been the standard since 1959 for AKM type rifles. You might be confusing either milled receiver ak47 versions or RPK 1.5-1.6mm receivers. The original AK47 in the 1940s Type one had a stamped receiver, but because of manufacturing problems they used a milled version untill they could work out the issues. If your comparing chinese or yugo rifles, they had a different mil spec and are not typical of an original AKM. Russian Vepr rifles in 7.62x39 are based off of the RPK concept and these have much heavier barrels and a thicker receiver of 1.5mm. Th -
Precise enough even with crappy inaccurate ammo to consistently sail a bullet into someone's eyesocket at 30 yards. Whether someone can make use of that level of precision is based on skill.
-
What's the best solvent to use for cleaning corrosive residue
my762buzz replied to LocoToro's topic in Saiga 5.45
Salts CAN NOT be neutralized. Acids can be neutralized. Bases can be neutralized. Neutralizing an acid or a base produces a salt. http://www.elmhurst.edu/~chm/vchembook/183neutral.htm Corrosive ammo is corrosive because it results in salt residues, NOT acid NOR base residues. Salts are ionic compounds which can dissolve in water. Hot water would have the best dissolving ability. Oil will not dissolve salts but will prevent or minimize the reactive nature of the salt which draws moisture from the air which would lead to corrosion. You can either remove the salt entirely and be d -
Question about bolt carrier hitting the trunion.
my762buzz replied to Bigtwin's topic in Saiga 7.62 X 39
I have never heard of someone wearing one out. -
What's the best solvent to use for cleaning corrosive residue
my762buzz replied to LocoToro's topic in Saiga 5.45
Salt residue needs to be flushed with water. When you sweat and observe salt crystals on your skin do you run to spray yourself with windex or head for the shower? If you get salt on your steel knives, forks, or spoons in the kitchen, do you hose your flatwear with windex or wash them? Hotter water works even faster. -
For Those Considering Poly-Coated Ammo For Long-Term Storage
my762buzz replied to BigChongus's topic in Saiga 7.62 X 39
Polycoating is useless. -
I got ahold of some Tula 122 gr hp , sorry no 124 gr Tula in my area yet. I compared it to an old Wolf 122 gr laquered cartridge, Mil Classic 8m3, and 1990s Uly Blue Label 8m3. I also did a needle probe and the Tula has the prefail cuts. I also did a depth comarison.
-
Eureka! The Holy Grail of ammo is mine!!!!
my762buzz replied to imarangemaster's topic in Saiga 7.62 X 39
Enough complaint emails to Tula might stop the poly crap coating. Attention Tula. The poly coating is garbage and is not helping anything. Please make the same 7.62x39 124 grain hollow point ammunition with laquered cases and mil spec sealant. info@tulammousa.com 110 N. IH-35 Suite 315-PMB #186 Round Rock, TX 78681 888-317-5810 | Fax: 512-218-8473 -
Eureka! The Holy Grail of ammo is mine!!!!
my762buzz replied to imarangemaster's topic in Saiga 7.62 X 39
Would a soft point mushrooming and cutting a hole that you can fit two fingers through be more effective than a hollow point that explodes and hollows out a fist size hole? 7n6 carries the poison bullet name, but 8m3 might as well be called "El Diablo" -
Abnormal wear? (Bolt carrier-rear trunion contact)
my762buzz replied to geofri's topic in Saiga 7.62 X 39
There are several factors to consider here. Checking powder types and powder weights would take a long time. Since saigas are basically modified ak74 mechanisms, the ak74 mil spec rounds would serve as an ideal mil spec model. Suppose someone observes how far a 5.45x39 saiga ejects 7n6 from the rifle. A 7.62x39 saiga should have nearly the same cycle speed and ejection distance. This sets a standard control. If 7n6 ejects 15 ft away on average, then any commercial 7.62x39 load should not eject any farther away. It would be good to note that even though many would consider muzzle exit ve -
Abnormal wear? (Bolt carrier-rear trunion contact)
my762buzz replied to geofri's topic in Saiga 7.62 X 39
A factory installed adjustable gas block sort of like the Saiga 12 or more like a multi level similar to a FAL might help with tuning the gas system to the specific load. Can anyone be 100% certain that their favorite loads are not overgassing the cycle and beating the hell out of their gun. The argument can be made that if it needed a gas regulator the original AK47, AKM, AK74M, or etc would have been designed that way. The problem is that a specific mil spec issue load is also designed around the original systems and a commercial NON mil spec load may increase the gas pressure at the gas bl -
Saiga 308 Spare Parts...How Much Would You $Pay$?
my762buzz replied to HB of CJ's topic in Saiga .308
Thanks for confirming. -
Well, I read the open letter and it makes perfect sense. 122 gr hp has been a Tula made long boattail bullet that the Wolf label used. 123 gr hollowpoint was always a bear bullet. 124 gr hp was Uly since the whilte box label/sapsan/mil classic. Vympel is golden tiger but no current hp offering in the USA. A Uly 8m3 bullet in a Vympel loaded golden tiger laquered case would be absolutely awesome. The dream team. Dear Great TULAMMO USA Customer, In connection with our ongoing promotion and support of TULAMMO products, we want to be sure that all of our customers are aware of the types o