buster charlie 0 Posted August 20, 2007 Report Share Posted August 20, 2007 If my buddy wants to use converted 30 round mags in his saiga .223 and keep it legal, without replacing the saiga's buttstock and handguard, what are his US parts count options? If I read it right he needs 4 US parts, so trigger, hammer, sear, gas piston would work. However the saiga has a weird composite trigger, what exactly is the PART that needs to be replaced? The trigger 'nub' in the traditional AK trigger pin location? The actual physical trigger you pull on? How could you replace that part? Gas piston, hammer, sear, now we're back to 3 parts. US magazines are not an option. I guess worst case scenario I could rig the gun up to use a US made AK polymer hand guard. The only reason he's not going US made furniture is he likes the low weight of the plastic stock set. So if I can't figure out the legalities of the 3 trigger parts, i'll probably go hammer, sear, piston, front hand guard. Any help is appreciated! Quote Link to post Share on other sites
kresk 10,063 Posted August 21, 2007 Report Share Posted August 21, 2007 (edited) You cannot just swap out the trigger group in a stock Saiga with a US-made G2 group. It must be converted to pistol grip configuration. And, Saigas have no sear, the FCG has a hammer/trigger/disconnector. Don't know if you're doing to be able to do it with the factory furniture still in use. Edited August 21, 2007 by tritium Quote Link to post Share on other sites
MD_Willington 11 Posted August 21, 2007 Report Share Posted August 21, 2007 There are examples here in the forums of how you can maintain the sporter appearance, including using a modified G2 FCG, from what I've seen here you need to modify the G2 so that it is the same as the stock Russian FCG. Do a bit of searching around here, I'm sure you'll find some of those posts. Quote Link to post Share on other sites
wlchase 0 Posted August 21, 2007 Report Share Posted August 21, 2007 (edited) BattleRifleG3 makes a modified FCG that can be used with the stock position. It replaces 2 of the 3 parts. Adding a piston yes, you're still short one. There are threads around about modifying and adding magazine followers and floorplates; either of those would bring you to the required count. Bill Edited August 21, 2007 by BillTX Quote Link to post Share on other sites
buster charlie 0 Posted August 22, 2007 Author Report Share Posted August 22, 2007 I'm right where I started. WHAT exactly is the trigger on the saiga? I could have a custom part machined, but I need to know what part to replace that would add 1 to the US parts count. So I take it the stock hammer and disconnecter would work, but what accounts for the trigger? Modifing the magazines is a non option. Quote Link to post Share on other sites
dayanx 1 Posted September 11, 2007 Report Share Posted September 11, 2007 I just got done talking to a LEO neighbor of mine that's never heard of this 922 reg. I described it to him and he said that he thinks because it sounds un-enforceable on its own, it may be used as an *icing* infraction to put a violent criminal away longer. Makes some sense to me. Quote Link to post Share on other sites
BullShark012 1 Posted September 14, 2007 Report Share Posted September 14, 2007 (edited) If my buddy wants to use converted 30 round mags in his saiga .223 and keep it legal, without replacing the saiga's buttstock and handguard, what are his US parts count options? If I read it right he needs 4 US parts, so trigger, hammer, sear, gas piston would work. However the saiga has a weird composite trigger, what exactly is the PART that needs to be replaced? The trigger 'nub' in the traditional AK trigger pin location? The actual physical trigger you pull on? How could you replace that part? Gas piston, hammer, sear, now we're back to 3 parts. US magazines are not an option. I guess worst case scenario I could rig the gun up to use a US made AK polymer hand guard. The only reason he's not going US made furniture is he likes the low weight of the plastic stock set. So if I can't figure out the legalities of the 3 trigger parts, i'll probably go hammer, sear, piston, front hand guard. Any help is appreciated! Why not just bolt on the ACE PG Stock set (2 US Parts) Then Get a Master Moulder 30 rd mag (3 US Parts) and your Done w/ just a bit of Dremel work on the Plastic Mag! (Legal w/ 30 rd mags) (just make it match the stock 10 rd. Russian mag Front and Rear Catches) Thats my option for my x 39, no Gunsmithing req'd ! to be 30 rd. Legal w/ 922r)....but I haven't checked if the ACE PG StocK Set is avail for the .223 - I have the 7.62 BS012 Edited September 14, 2007 by BullShark012 Quote Link to post Share on other sites
nalioth 405 Posted September 14, 2007 Report Share Posted September 14, 2007 For Petes sake, just change out the gas piston and tell him to not buy any magazines but US made ones. Quote Link to post Share on other sites
BullShark012 1 Posted September 14, 2007 Report Share Posted September 14, 2007 For Petes sake, just change out the gas piston and tell him to not buy any magazines but US made ones. Changing out the Piston reguires some Drill Press work, right? That's why I suggested the ohter option....but you are right really..that's the Best way. Quote Link to post Share on other sites
Navy87Guy 1 Posted September 14, 2007 Report Share Posted September 14, 2007 (edited) Changing out the Piston reguires some Drill Press work, right? That's why I suggested the ohter option....but you are right really..that's the Best way. No -- all you need is a hand drill and a hammer. Drill out the pin that holds the piston onto the bolt carrier, unscrew it, screw the new one on, then drill the new hole, insert a pin and peen it over. Start to finish, the whole process takes about 15 minutes. You can either get a specific pin for the piston 3 mm), or you can use a small nail. There's a guy called Hotbarrel over on Gunco.net that sells US-made gas pistons for $15 each (delivered). I got one and it very well done (it does has the grooves, though, not the smooth head). Easy and permanent. As far as the trigger -- it is just that: the curved portion that extends through the bottom of the receiver. It is connected to the disconnector which uses that funky yoke to activate the hammer. You can replace the hammer pretty easily. The best bet for the trigger/disconnector is to get the set from BR3G or Dinzag. Jim Edited September 14, 2007 by Navy87Guy Quote Link to post Share on other sites
PlinkinPark 0 Posted September 17, 2007 Report Share Posted September 17, 2007 Changing out the Piston reguires some Drill Press work, right? That's why I suggested the ohter option....but you are right really..that's the Best way. No -- all you need is a hand drill and a hammer. Drill out the pin that holds the piston onto the bolt carrier, unscrew it, screw the new one on, then drill the new hole, insert a pin and peen it over. Start to finish, the whole process takes about 15 minutes. You can either get a specific pin for the piston 3 mm), or you can use a small nail. There's a guy called Hotbarrel over on Gunco.net that sells US-made gas pistons for $15 each (delivered). I got one and it very well done (it does has the grooves, though, not the smooth head). Easy and permanent. As far as the trigger -- it is just that: the curved portion that extends through the bottom of the receiver. It is connected to the disconnector which uses that funky yoke to activate the hammer. You can replace the hammer pretty easily. The best bet for the trigger/disconnector is to get the set from BR3G or Dinzag. Jim Are the trigger/disconnect US made and do they drop into thestock location? Quote Link to post Share on other sites
nalioth 405 Posted September 17, 2007 Report Share Posted September 17, 2007 Changing out the Piston reguires some Drill Press work, right? That's why I suggested the ohter option....but you are right really..that's the Best way. No -- all you need is a hand drill and a hammer. Drill out the pin that holds the piston onto the bolt carrier, unscrew it, screw the new one on, then drill the new hole, insert a pin and peen it over. Start to finish, the whole process takes about 15 minutes. You can either get a specific pin for the piston 3 mm), or you can use a small nail. There's a guy called Hotbarrel over on Gunco.net that sells US-made gas pistons for $15 each (delivered). I got one and it very well done (it does has the grooves, though, not the smooth head). Easy and permanent. As far as the trigger -- it is just that: the curved portion that extends through the bottom of the receiver. It is connected to the disconnector which uses that funky yoke to activate the hammer. You can replace the hammer pretty easily. The best bet for the trigger/disconnector is to get the set from BR3G or Dinzag. Jim Are the trigger/disconnect US made and do they drop into thestock location? The above advice was aimed at you keeping the rifles appearance stock while conforming to 922r. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.