kyphur 0 Posted February 12, 2011 Report Share Posted February 12, 2011 I did a search and came up empty but I was just wondering if the front site screwed out. I have access to a shotgun front sight kit with different threadings but I didn't want to take a set of pliers to it and tear it up without knowing for sure. Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted February 12, 2011 Report Share Posted February 12, 2011 If you have a newer S-12, it's staked in place and cannot be unscrewed. The early models were threaded and could be easily removed. They kept coming out and getting lost so the factory changed the way they were doing them. I believe this was somewhere around ' 05 or so. It's easy to tell though....if your front bead has a ball looking shape to it, instead of a more flattened cone shape, it's non threaded. With those you have to grind them off flush with the surface. You can then drill them out and thread, but be careful no to do it with the puck installed, or booger up the inside of the gas block. Also of course, don't screw anything down in there that will protrude to the inside and get in the way. 3 Quote Link to post Share on other sites
kyphur 0 Posted February 12, 2011 Author Report Share Posted February 12, 2011 Thanks for the response! It's the newer style so I will leave it be. No big deal for me. Quote Link to post Share on other sites
YOT 3,743 Posted February 12, 2011 Report Share Posted February 12, 2011 If you have a newer S-12, it's staked in place and cannot be unscrewed. The early models were threaded and could be easily removed. They kept coming out and getting lost so the factory changed the way they were doing them. I believe this was somewhere around ' 05 or so. It's easy to tell though....if your front bead has a ball looking shape to it, instead of a more flattened cone shape, it's non threaded. With those you have to grind them off flush with the surface. You can then drill them out and thread, but be careful no to do it with the puck installed, or booger up the inside of the gas block. Also of course, don't screw anything down in there that will protrude to the inside and get in the way. This is precisely what I did, with the addition of some epoxy putty between the sight and gas block, then screwed down. 2 Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted February 12, 2011 Report Share Posted February 12, 2011 Nice! ^ 1 Quote Link to post Share on other sites
YOT 3,743 Posted February 12, 2011 Report Share Posted February 12, 2011 Thanks, Cobra. What a huge difference it makes acquiring that front sight. Quote Link to post Share on other sites
gremlinx 20 Posted March 17, 2011 Report Share Posted March 17, 2011 (edited) What sight is that? I didn't see it on their websight. Edited March 17, 2011 by goober Quote Link to post Share on other sites
YOT 3,743 Posted March 17, 2011 Report Share Posted March 17, 2011 (edited) Tru-Bead Universal. It's on their website on the "wing shooting" page, but I got it at Dick's on sale. Come with 5 different color replaceable fibers and several different size screws. It was very easy to put on, once I decided to go past the point of no return and grind off the factory sight and drill into the gas block. I didn't drill all the way through, just deep enough for the screw, and it seems that the screw is much harder than the gas block because it self-tapped into the hole (I tried it on scrap first). ETA: It is the same height as the factory sight if you don't take off anything besides the bead and serrated part if the rib. Part #TG949A Edited March 18, 2011 by Yeoldetool Quote Link to post Share on other sites
Czar 1 Posted March 18, 2011 Report Share Posted March 18, 2011 (edited) Tru-Bead Universal. It's on their website on the "wing shooting" page, but I got it at Dick's on sale. Come with 5 different color replaceable fibers and several different side screws. It was very easy to put on, once I decided to go past the point of no return and grind off the factory sight and drill into the gas block. I didn't drill all the way through, just deep enough for the screw, and it seems that the screw is much harder than the gas block because it self-tapped into the hole (I tried it on scrap first). ETA: It is the same height as the factory sight if you don't take off anything besides the bead and serrated part if the rib. Part #TG949A Do you remember what size screw you used to install it? Also, do you have a pic from the side? Edited March 18, 2011 by Czar Quote Link to post Share on other sites
YOT 3,743 Posted March 18, 2011 Report Share Posted March 18, 2011 Yes, it was the smallest screw in the package, in case I had to enlarge the hole for some reason. Got it right the first time though. This pic is before it was finished and painted. Quote Link to post Share on other sites
gremlinx 20 Posted March 18, 2011 Report Share Posted March 18, 2011 I found a cheap hi viz Screw on, with a chambered hole.. I think it mounts with a 6/32 screw? 4-40? Something like that... Quote Link to post Share on other sites
FORKLIFT352 63 Posted March 18, 2011 Report Share Posted March 18, 2011 Mine was the ball type and it fell out while I was taking off the gas block. I diddent bother putting it back. It looked like it screwed in with like 2 threads. Quote Link to post Share on other sites
Czar 1 Posted March 20, 2011 Report Share Posted March 20, 2011 Yes, it was the smallest screw in the package, in case I had to enlarge the hole for some reason. Got it right the first time though. This pic is before it was finished and painted. How much did you grind to get the base of the FO sight flat against the GB? I bought the same FO today, but the FO base is longer than the elevated portion on the GB. Quote Link to post Share on other sites
YOT 3,743 Posted March 20, 2011 Report Share Posted March 20, 2011 Sorry, I thought I explained that already, but it was in a different thread. The only thing I ground off was the bead and post, and the serrated part of the rib. This leaves a small flat area to work with between the two spots that were ground off. I then filled the ground areas and under area the that extends past the rib with an epoxy putty before screwing down the sight. After the putty was hard I very carefully filed away the excess. Some of it can be trimmed with a sharp knife as it's hardening. Hope this helps. Quote Link to post Share on other sites
Czar 1 Posted March 20, 2011 Report Share Posted March 20, 2011 Sorry, I thought I explained that already, but it was in a different thread. The only thing I ground off was the bead and post, and the serrated part of the rib. This leaves a small flat area to work with between the two spots that were ground off. I then filled the ground areas and under area the that extends past the rib with an epoxy putty before screwing down the sight. After the putty was hard I very carefully filed away the excess. Some of it can be trimmed with a sharp knife as it's hardening. Hope this helps. Thanks. Quote Link to post Share on other sites
Guns Are Great 140 Posted March 20, 2011 Report Share Posted March 20, 2011 that is a super nice set of furniture you got there! it would really look good with a CSS trigger guard! Yes, it was the smallest screw in the package, in case I had to enlarge the hole for some reason. Got it right the first time though. This pic is before it was finished and painted. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.