IndyArms 10,186 Posted December 30, 2006 Report Share Posted December 30, 2006 I figured this should be posted in the .223 section as well, as its the same info, pretty much. http://forum.saiga-12.com/index.php?showtopic=7652 Enjoy! Quote Link to post Share on other sites
Messiah Jones 2 Posted January 26, 2008 Report Share Posted January 26, 2008 I figured I'd post what little I know about threading a barrel for a muzzle brake or compensator. I hope this isn't redundant, I just figured it may help someone. For a long time during the "Clinton Assault Weapons Ban" it was illegal to have a threaded muzzle except on pre-ban rifles. Now that the ban is history most people can legally have threaded barrels (check your local and state laws). There are three sizes of threads used among AKs that I know of. 14mm, 22mm and 24mm. I've never seen a 22mm threaded barrel or brake so I have to assume they are more rare. The 14mm uses left hand threads, but the 24mm uses right hand threads. I'm not sure about the 22mm. Most muzzle brakes out there were designed for the older style AK-47 threaded barrel. Therefore the most common thread size is 14mm X 1 Left Hand. In order to thread your barrel to 14mm to accomodate these brakes your barrel must be about 0.52" - 0.58" O.D. This diameter barrel is common among military AKs and SKSs. Muzzle diameters vary among manufacturers, especially with commercial AKs. But most of the military AKs will have the correct barrel O.D. to be threaded to 14mm. The current military issue brakes on the AK-74s are threaded to 24mm. Here are two pictures comparing a 14mm AK-47 brake to a 24mm AK-74 brake. Top is 14mm AK-47, bottom is 24mm AK-74. Left is 24mm AK-74 brake, right is 14mm AK-47 brake. Some of the Romanian rifles had their muzzles turned down so that they couldn't be threaded. I had a 2002 SAR-1 that had the correct barrel diameter. I think a little later they started turning them smaller. I don't know how they do it now that the ban expired. If you want to use the larger 24mm AK-74 style brakes, you have two choices. You can thread your barrel to 14mm LH and get an adaptor to allow the use of the 24mm brake, or you can buy the whole front sight block/threaded sleeve combo. The adaptor is available here... www.ak-103.com and looks like this. The whole front sight block/threaded sleeve combo is at www.k-var.com and looks like this. Another issue is plunger pins. The plunger pin is spring loaded and sticks out of the front sight block. It's job is to catch the brake in the groove and ensure that it can't unscrew and fall off. Plunger pins and springs are available at www.k-var.com . In order to install one you must remove the front pin that holds the front sight block on, insert the spring and plunger pin into the hole, and then reinsert the front sight block pin. A commercial AK such as a Saiga, Veper etc. probably won't have the plunger pin hole. Here's what I'm talking about. Here's a picture of the plunger pin with a 24mm brake. Finally, don't be afraid to thread your barrel. It's very easy. I had never done it before, but I rented a kit and had it done within five minutes without a hitch. Here's what you'll need... 1. Threaded Bore Pilot (TAT) 2. Threading Die 3. Die Handle ... and everything can be found here. http://www.preciseinnovationsllc.com/threadingkits.htm or you can rent one from someone online like myself. Good luck on your project :!: Tat Die Handle Threading Instructions: The Threading Kit contains a THREADING ALIGNMENT TOOL (TAT) that is designed specifically to facilitate the creation of threads on the outside of rifle muzzles that are both concentric and perpendicular to the rifled bore. Your TAT package contains three parts: 1. Threaded Bore Pilot (TAT) 2. Threading Die 3. Die Handle Warning: Instructions are for right-hand threading. For left-hand threads, turn the opposite direction. The TAT is simple to use. Even for the inexperienced, the entire procedure should not take more than five to ten minutes. For your safety, follow these directions carefully: 1. Open the action on the rifle and be sure there is no ammunition in the magazine or the bore. 2. The threading die is split along one side and has screw to adjust the die cut for shallow or deep threads. Open up the die to cut shallow threads in order to start the initial threads on the rifle muzzle. 3. Install the threading die into the die handle. Begin with the large chamfered side facing the muzzle. Insert the die into the handle and tighten the retaining screws so that the die will not turn in the handle. 4. Locate the threaded bore pilot (TAT) and insert the pilot into the threaded die so that the pilot, or the unthreaded end, goes into the die from the side opposite the large chamfer. Turn the threaded bore pilot threads two full turns into the die. Use either your muzzle brake or your flash hider as a jam nut to hold the bore pilot in the die. Tighten firmly. 5. If you have assembled the TAT properly as described above, the die now has about three turns available to cut threads on the chamfer side of the die. The TAT is now ready to use. 6. Hold the barrel of your rifle firmly during the threading procedure. A good bench vice with padded jaws is desirable to hold the barrel. You can use soft wood blocks, sheet lead, or copper sheet as padding for the vice jaws. 7. Lubricate both the pilot and die inside of the muzzle with oil. Now insert the lubed pilot into the bore of the muzzle until the die contacts the muzzle. Grasp die handles in both hands and, using some pressure, rotate the handles in a clockwise direction. You will feel the die start to cut. Keep turning the handles slowly. There should be some resistance until the threading dies bottom out on the pilot (above three full turns). 8. WARNING: When you encounter any resistance, STOP! Do not go any further, remove the TAT, then continue threading. With proper threading, the TAT can last for years. Damaged die can be replaced at the regular price. 9. Leave the die attached to the muzzle. You have established a threading pattern that is both concentric and perpendicular to the bore. Loosen the muzzle brake or flash hider that served as a jam nut and remove the threaded pilot from the die. Grasp the die handle again with both hands, turn the handles clockwise until the die bottoms out against the front sight. 10. Now turn the die handles counter-clockwise and remove the die from the rifle muzzle. At this point, you have established the muzzle threads and all you have to do now is deepen the threads so the muzzle brake will screw on. The pilot is no longer necessary. 11. Remove the threading die from the handle and readjust the die a small amount so that the die will cut slightly deeper threads. Install the die back in the handle. Orient the die so that the side with the chamfer again faces the muzzle. Carefully start the die back on the established threads by turning the die handles clockwise. Continue turning the handles until the die bottoms out against the front sight. Unscrew the die. 12. Try to turn the muzzle brake onto the threads that you cut. If the brake will not start onto the treads, repeat Step # 10 above and try again. You want a good tight fit on the threads with some resistance. You may have to repeat the procedure several times. 13. STOP when you are able to turn the brake on the muzzle at least four or five turns with resistance. Remove the brake from the muzzle. Now take the die that is still installed in the handles and turn the die over. The side with the chamfer should be facing you now. Again, carefully start the die onto the established muzzle threads and turn the die handles clockwise until the die bottoms out against the front sight. Unscrew the die from the muzzle. You are now done threading. Clean any thread cutting from the muzzle threads with a soft wire brush and install the muzzle brake until the base butts against the front sight. Make the unit quite tight. If you have followed the 13 procedure steps above, your muzzle brake is now properly installed and ready for use. GOOD SHOOTING! ORIGINAL THREAD SIZES RIFLE CALIBER THREAD SIZE AR-15, M-16, AR-180 .223 (5.56mm) 1/2x28 AR-15, M-16, AR-180 9mm 1/2x36 Ruger Mini 14 (blue) .223 (5.56mm) 9/16x24 Ruger Mini (stainless) .223 (5.56mm) 9/16x24 Ruger Mini 30 (blue, stl) 7.62x39 5/8x24 HK-91/ G-3 308/ 7.62 15x1 HK-93/ 33/ G-53 .223 (5.56mm) 15x1 HK-94/ MP-5 9mm 9/16x24 US M1/M2 Carabine 30 9/16x24 FN-FAL US Match 308 (7.62) 9/16x24 FN-FAL Para/ SAR-48 308 (7.62) 9/16x24 FN Heavy Barrel 308 (7.62) 11/16x24 STEYER AUG .223 (5.56) 13x1 LH AKM/ AK-47 0.223 14x1 LH AKM/ AK-47 7.62x39 14x1 LH GALIL 308 (7.62) 13x1 RH GALIL .223 (5.56) 13x1 RH UZI Carabine/ SMG 9mm 5/8x24 UZI Carabine 0.45 M1A/ M-14 308 L1-A1 308 9/16x24 MAS 1949-56 308 17x1 EDIT: Here are some pics of my theading jobs. Two of these rifles are converted Saigas and the third is a SAR-1. The Saigas have a "sleeve" around the muzzle which extends from the front sight. That has to be removed in order to thread the barrel. I tried punching out the pins and hammering the front sight off, but it was so tight it wouldn't budge. I ended up cutting the "sleeve" off of one Saiga with a Dremel tool and cutting disc. That was tedius and ended up crooked, requiring a lot of filing. Finally I looked down and noticed a tool under a bunch of junk and it turned out to be exactly what I needed. A pipe cutter! That made it so much easier. The Saigas muzzle is longer than other AKs. Don't make the mistake of cutting the sleeve back too far or your brake won't screw on all the way. Figure out how much you brake will screw on and only cut the sleeve back that far. I learned this one the hard way. :roll: When you thread the barrel put the kit together like this. Use the brake to firmly hold the TAT in place in the die. It really helps. Then you just clamp the rifle in a vice and turn the threading kit counter-clockwise until you've threaded it far enough. Easy as pie. Quote Link to post Share on other sites
gothchick 0 Posted April 13, 2009 Report Share Posted April 13, 2009 Very nice write up. :-) Quote Link to post Share on other sites
CPE1704TKS 24 Posted January 2, 2010 Report Share Posted January 2, 2010 Looks like a number of the images are no longer available. Quote Link to post Share on other sites
Coaxel60 3 Posted November 24, 2010 Report Share Posted November 24, 2010 Lots of great info....Thanks much Quote Link to post Share on other sites
josey88 21 Posted February 18, 2011 Report Share Posted February 18, 2011 (edited) Gosh, I have learned so much here , that I am now able to attempt a lot of things. I have a Saiga .223 , 20" barrel incoming next week and I will be doing the conversion myself. I have the plugs, binding posts , tools, etc ready. The Tapco G2 single hook kit is on the way , along with the AK gas tube , The Tapco Intrafuse handguard and the bolt on retainer for the lower handguard (I can`t believe I paid $50.00 for the damn thing , but I am not planning on taking off the sight or the gas block to mount it) ... I reasoned that I would prefer to peel off the sleeve on the barrel and thread it(I don`t know if it is threaded or not , but I am assuming ; if it is threaded , good for me ) and install an adapter for the 24mm brake , instead of taking off the whole front sight . The idea of doing that is not appealing to me , because of the alignment of the sight, pinning it , etc ... at least not yet. So, I would be installing the adapter , the 24mm brake (all those parts are also on the way) and I have discovered an old thread from someone that thought out the same thing : how to drill and install a keeper pin and spring on the front sight . Since the adapter and the muzzle brake that I bought have the indentation for the pin , it will come out great. I guess I have a busy week ahead... Edited February 18, 2011 by josey88 Quote Link to post Share on other sites
g21322635 2 Posted May 3, 2011 Report Share Posted May 3, 2011 Dinzag is great to deal with I sent him barrel dimensions on my Saiga 223 and he told me what to order and I sent him a usps money order for the parts they came in and followed instructions and now have a great flash suppressor to tame the flash. Parts are good quality and reusable. Thumbs up. Quote Link to post Share on other sites
chunga 31 Posted October 9, 2011 Report Share Posted October 9, 2011 My Lufkin micrometer tells me the O.D. measured as close as I can get to the rear of the FSB is 0.564". Can anyone please confirm that is a reliable point to take my measurement? I'd like to wait until I have the Phantom Flash Hider in my hand before removing the shroud because I don't believe I want to remove all of it. I'm pretty sure the parts below are correct but would prefer to be completely sure before I place my order with Dinzag. # PFH1410 - $30 - For 14x1 LH barrels - common for most AK's with 0.551" to 0.569" barrel o.d.'s # DIE14X1LH - $30 - M14X1LH Die for 0.551" to 0.571" o.d. barrels If anyone wants to prepay shipping they can have the die and TAT once I'm done. I can't think of any other use for it. Quote Link to post Share on other sites
Saigagenesis 0 Posted October 16, 2011 Report Share Posted October 16, 2011 I'm interested, as I'm going to install a phantom as well. Quote Link to post Share on other sites
chunga 31 Posted October 21, 2011 Report Share Posted October 21, 2011 @ saigasturn. Ok, hang on. I finished mine yesterday but two friends local to me are ordering parts and want to use it first. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.