bcmsaiga 8 Posted November 3, 2014 Report Share Posted November 3, 2014 So I just picked up and then went and shot my new saiga iz-240. its awesome and the headspace is fine. shot red army and silver bear. So.. should i run a recoil buffer from carolinashooter supply? i ask because it definatly makes contact every time with the rear trunnion and its already starting to peen. i have seen this on almost all saigas and i used to run the recoil buffers. how do you guys feel about a buffer? would it possible do more damage to the rivets holding the rear trunnion due to shorteing the space between the bolt carrier or would it do less damage because it is hitting soft material? Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 3, 2014 Report Share Posted November 3, 2014 Feel? Nothing. What I have experienced is simple. They do a job like any other part and like any other part get the best quality available or leave it off. Like anything else even informed opinions will vary. 1 Quote Link to post Share on other sites
Matthew Hopkins 1,065 Posted November 3, 2014 Report Share Posted November 3, 2014 (edited) buffers, waste of money better spent elsewhere. I have 5 AKs that I have put at least 9K or better rounds through the years I had them, and not one of them has any issues with rear trunnions being loose rivets loose etc.... the buffers are nothing but a marketing gimmick for you to spend money you don't need to spend Edited November 3, 2014 by Matthew Hopkins Quote Link to post Share on other sites
BigChongus 765 Posted November 3, 2014 Report Share Posted November 3, 2014 Post pics of the peening. The vast majority of AKs out there make contact with the rear trunnion. If you're still uneasy about it, a Wolff +15% spring is a better remedy than a buffer IMO. 3 Quote Link to post Share on other sites
bcmsaiga 8 Posted November 3, 2014 Author Report Share Posted November 3, 2014 ok sounds good. i have another issue. i just installed my flat style bullet guide i got from carolina shooter supply and on the last round if i go to feed it with my fingers (with the bolt carrier out of the gun) the round jams right below the opening of the chamber but if i rack the action it will cycle the last round. sometimes if cycled with the bolt (the last round) it will mess up the tip of the bullet a bit. anybody have issues with this? do i need to try a different bullet guide from somewhere else like dinzag or should i try and make a space for it or something. it just seems it needs to be a couple thous higher or something. Quote Link to post Share on other sites
poolingmyignorance 2,191 Posted November 3, 2014 Report Share Posted November 3, 2014 Try a different mag. I have one or two that do it, occasionally. I've never had it actually create a problem. Quote Link to post Share on other sites
bcmsaiga 8 Posted November 3, 2014 Author Report Share Posted November 3, 2014 ..i cut a piece of aluminum can to make a shim and it seemed to help some. as long as it cycles when firing thats all i care about. it does seem to dive just a bit still with a couple of mags but if put the bolt and carrier in without the spring and lightly push it forward, it picks the round right up. this is only on the last round for all the other ones feed perfectly-even without the b/g. Quote Link to post Share on other sites
mancat 2,368 Posted November 3, 2014 Report Share Posted November 3, 2014 (edited) Buffers increase the chance of the action short stroking. If they were needed, the design would include one. I had the Wolff XP spring in my .223 for a while. It occasionally caused the rifle to short stroke or double fire. Youe milage may vary. Edited November 3, 2014 by mancat 2 Quote Link to post Share on other sites
thebuns1 4,323 Posted November 3, 2014 Report Share Posted November 3, 2014 Waste of money. Quote Link to post Share on other sites
bcmsaiga 8 Posted November 3, 2014 Author Report Share Posted November 3, 2014 So do not run a buffer and let this trunnion peen up...i only shot 100 rounds today, i would hate to see what it looks like in 5000,, i dont think there would be anything left. is it gonna hurt anything to run a buffer? Quote Link to post Share on other sites
mancat 2,368 Posted November 3, 2014 Report Share Posted November 3, 2014 It will look the same in 5000 rounds. 2 Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 3, 2014 Report Share Posted November 3, 2014 Its cheap, even a good one, not going to break the bank nor blow up the rifle. Told you opinions vary and I wont bore you with anecdotal evidence. Your rifle your call Quote Link to post Share on other sites
bcmsaiga 8 Posted November 3, 2014 Author Report Share Posted November 3, 2014 Ok rhodes so what is the best buffer? it would make sense that it COULD do more damage but if it truly is hitting really hard on the rear trunnion wouldnt metal to metal be worse than metal to rubber? i ordered bother the wolff extra power recoil spring and a buffer from carolina shooter supply. i have always ran a buffer, even my 80k+ round ak47 (saiga) has had one for about 78,000 of the rounds through it with no sign of rivets deforming, it also has the wolff XP spring. Quote Link to post Share on other sites
G O B 3,516 Posted November 3, 2014 Report Share Posted November 3, 2014 (edited) I use BJB's in the guns that work with them. Some will not work right with a buffer. The wife;s S-.410 with a Yugo UF will jump the rails without one. Edited November 3, 2014 by G O B 1 Quote Link to post Share on other sites
bcmsaiga 8 Posted November 3, 2014 Author Report Share Posted November 3, 2014 So if I throw one from the CSS the blue one in my saiga it will not pop the rivets out from the bcg hitting it? Quote Link to post Share on other sites
thebuns1 4,323 Posted November 3, 2014 Report Share Posted November 3, 2014 The rivets won't pop out regardless. 4 Quote Link to post Share on other sites
BigChongus 765 Posted November 3, 2014 Report Share Posted November 3, 2014 It sounds in general like you're really underestimating the durability of the platform. 3 Quote Link to post Share on other sites
mancat 2,368 Posted November 3, 2014 Report Share Posted November 3, 2014 (edited) So you have EIGHTY THOUSAND rounds (well over $10k worth of ammo) through a Saiga, with a buffer in it for 78K of those rounds, and you're just now asking us if a buffer is OK to use? Was that a typo? Edited November 3, 2014 by mancat 4 Quote Link to post Share on other sites
JoeAK 337 Posted November 3, 2014 Report Share Posted November 3, 2014 Here's my 7.62 bolt carrier and trunnion after 4,300 rounds, no buffer. And here's my 5.45 bolt carrier and trunnion after 1,900 rounds, no buffer. Not much difference, they tend to wear to a certain point pretty quickly, then wear very slowly, they've looked like this since they've had just a few hundred rounds through them. A buffer probably wouldn't hurt, but it's not really needed either. Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 4, 2014 Report Share Posted November 4, 2014 I use blackjack but that isnt an endorsement. Just a good buffer. Use them on a couple of rifles that require them, one S308 with techsights and another with TWS dogleg. That rifle requires a buffer, shipped with steel but with the modifications that has to go so on with the BJB. Also use one on a Sx39 but it is not required just an attempt to soften the jar on an arthritic shoulder, aint high school football great. Works fine always has and yeah I keep spares. I am thinking this has gone as far it can, good luck. 1 Quote Link to post Share on other sites
bcmsaiga 8 Posted November 4, 2014 Author Report Share Posted November 4, 2014 Yes it has thank you all for your input. The reason I start asking now is because I never heard anything bad about them until recently. And I never look at it that way about the cost of ammo because I usually dont have to pay money for mine. I do a lot of "work" for it usually. And the saiga rifle is more important to me than money is at this point being that they are banned. i just want it to last as long as possible. thanks again guys. Quote Link to post Share on other sites
evlblkwpnz 3,418 Posted November 4, 2014 Report Share Posted November 4, 2014 buffers, waste of money better spent elsewhere. I have 5 AKs that I have put at least 9K or better rounds through the years I had them, and not one of them has any issues with rear trunnions being loose rivets loose etc.... the buffers are nothing but a marketing gimmick for you to spend money you don't need to spend +1 Quote Link to post Share on other sites
JESS1344 508 Posted November 4, 2014 Report Share Posted November 4, 2014 GUYS, THE PHRASE "WORK HARDENING STEEL" COMES TO MIND..... ANY METALURGISTS OUT THERE CARE TO COMMENT? JESS1344 Quote Link to post Share on other sites
Matthew Hopkins 1,065 Posted November 4, 2014 Report Share Posted November 4, 2014 i just want it to last as long as possible. that SAIGA will outlive you. why people think they have to baby a AK is a mystery to me. Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 4, 2014 Report Share Posted November 4, 2014 i just want it to last as long as possible. that SAIGA will outlive you. why people think they have to baby a AK is a mystery to me. Hmm different subject, perhaps it will but machines break no matter how well built and that AK is a machine. Still it is a crying shame one cant even get an extractor or firing pin, which do break rarely and could be easily replaced. This is why I stopped buying Saigas and have considered selling them for rifles that can be maintained. No Stoners but there are options at least for now. Will keep one for that jic situation where maintenance is immaterial. So baby away, it doesnt hurt a damn thing. Quote Link to post Share on other sites
BigChongus 765 Posted November 4, 2014 Report Share Posted November 4, 2014 i just want it to last as long as possible. that SAIGA will outlive you. why people think they have to baby a AK is a mystery to me. Hmm different subject, perhaps it will but machines break no matter how well built and that AK is a machine. Still it is a crying shame one cant even get an extractor or firing pin, which do break rarely and could be easily replaced. This is why I stopped buying Saigas and have considered selling them for rifles that can be maintained. No Stoners but there are options at least for now. Will keep one for that jic situation where maintenance is immaterial. So baby away, it doesnt hurt a damn thing. How can you not get extractors or firing pins? Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 4, 2014 Report Share Posted November 4, 2014 i just want it to last as long as possible. that SAIGA will outlive you. why people think they have to baby a AK is a mystery to me. Hmm different subject, perhaps it will but machines break no matter how well built and that AK is a machine. Still it is a crying shame one cant even get an extractor or firing pin, which do break rarely and could be easily replaced. This is why I stopped buying Saigas and have considered selling them for rifles that can be maintained. No Stoners but there are options at least for now. Will keep one for that jic situation where maintenance is immaterial. So baby away, it doesnt hurt a damn thing. How can you not get extractors or firing pins? You got a source for the various models??? Quote Link to post Share on other sites
thebuns1 4,323 Posted November 4, 2014 Report Share Posted November 4, 2014 ^^ kvar has them. Maybe not in stock at the moment. Quote Link to post Share on other sites
Rhodes1968 1,638 Posted November 4, 2014 Report Share Posted November 4, 2014 They never had any parts for the S308 that I am aware and the more "standard" x39 is spotty at best so basically there are no spares. Springs maybe and even then its just best fit not what was shipped. Quote Link to post Share on other sites
thebuns1 4,323 Posted November 4, 2014 Report Share Posted November 4, 2014 What do you mean by spotty?. I've seen several parts on their site for Saigas. Just not the 308 or x54. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.