wpflgun

My take on a skeleton buttstock, from scratch...

If you are running a Saiga .223 w/o bullet guide, listen up: Bortach has these on sale as of this post, 140 in stock. SGM Saiga .223 30rd Rifle Magazines Log In, Register, Or Add To Cart To See If Special Pricing Is Available For This Product RRP: $34.26 Your Price: $15.00 (You save $19.26) Brand: SGM Tactical SKU: SGM-SSGMP223 Inventory: 140 To purchase out of stock or quantities greater than inventory shows please Click Here Quantity: Free Shipping USA

So, is this why unmodified Galil mags fit after removing the trunnion material for magwell adapter installation? Also, If I were to build a .223 on an AK-74 kit, would the trunnion require removal of material for the adapter?

You will need to install a handguard retainer for this one on your Saiga, as it fits the standard AK configuration. I am not sure if you would need a different gas tube, need to check and see. The model MNT-HGSG39 is the one that will fit your Saiga w/o requiring a handguard retainer. If I remember correctly, it makes use of the pins protruding under the gas block of the Saiga for stability. If you don't wind up using it, I would be interested in possibly tradiing you something for it, as I have an AK build project about to start.

+1 Surprisingly compact, best sub 9mm round, built like a tank. Has a bad rep for double action trigger pull, but not any worse than my snubby revolver. As others have stated, given the adrenalin rush, it is actually a plus IMHO.

Mine fit reasonably tight beforr doing the Renegade Buck AR magwell adapter. After the front trunnion material was removed, they wobbled more than I was comfortable with. Not wanting them to go to waste, I added a bit of JB Weld to the sides and more so the front of the mags, which got rid of most of the excessive wobble. I had some steel Galils which were modified prior to the adapter installation which I did the same fix for. I love the AR adapter, runs like a top. I found that he Tapco and Galil mags both fit unmodified since the trunnion material was removed for the adapter. Previo

PM sent.

I have seen a tab with sling hole which mounts between the forward mounted pistol grip and the receiver, shouldn't be difficult to fabricate something similar. Another thought: How about a mounting point reinforcement allowing the use of the holes from removing the factory trigger assembly?

I have found that the 25 yard mark is about right for getting in the ballpark on paper. There is a slight arc that on most rounds (not sure about .223) comes pretty close on the 100 yard mark after tweeking it at 25 yards.

I went with the Renegade buck adapter, but would have no qualms going with MSA. I have had a great experience, although I underestimated the amount of material to be removed. I went very slow and now have a great fitting adapter that loves AR mags of all types. As a result of the material removed for the adapter, I have found that both Galil steel and Tapco Galil/Golani mags fit pretty well without modification. Prior to removing the trunnion material for the adapter, Galil's had to have the front area ground down in order for the mag to seat properly (instructions elsewhere on this sit

I was wondering if one or two screws could be used to help secure some kind of a side mount rear aperture sight......

You need the AK/SKS Sight tool, it will make easy work of adjusting it. Here is one place you can get one: http://centerfiresys...m/TOOSKS04.aspx

I would grind it to a more uniform shape on top, clean it up and re-seat it with JB Weld underneath. If you prepare the surface properly, it shouldn fill up the space and hold with the screw. I have used it beneath my home made guide, which had some space, and it has held up for over a thousand rounds. Since the metal surface of the guide is all that contacts the bullet, there is not a problem with it chipping. Worst case is it won't work and you are no worse off. The JB Weld is easy to remove, and you go to plan B. Just remember to use the industrial strength that takes 8-10 hours t

The only real issue for .223 Saiga's, assuming a basic conversion moving the trigger group forward, add pistol grip and change butt stock and installing a bullet guide is the issue of magazines. Set the magazine issue aside and you have legendary AK ruggedness and reliability firing standard .223 ammo. If you want to use standard AK mags, there are few choices, and they typically require modifications to work. I elected to install an AR magwell adapter on mine and have 100% reliability using milspec and aftermarket AR mags.

It sounds like a good concept, too bad it is MIA. I got a Renegade Buck adapter last year and love it, solved all the mag problems, very reliable. Semi-permanent would be good.