toshbar 36 Posted December 21, 2010 Report Share Posted December 21, 2010 (edited) I just got the furniture in today and put it together. All the Bulgy surplus was CAKED with grease. I spent an hour and a half with my steam cleaner getting it off. I pulled the buttplate off the stock and it was half full of old grease. The lower handguard went on well. I filed the notch too far forward and had about 1/16" front to back slop, so out came the mig welder..... I put one tack on the front of my groove and refiled to allow the bolt to go through. I used the bolt that came with it and did not trim the threads in the middle. I could see light through the handguard right behind the retainer on the bottom, so I drilled that out and installed a sling stud with a nut on the back(inside the handguard). Then came the gas tube(east german AKM).....It took some trimming off the part that touches the cam lock, and also the bottom of the front retainer touched the lower handguard retainer and was pushing on it too hard, so that got the bench grinder treatment too. I painted over all my shiny surfaces with some black spray paint and was done with all the fitting. Pistol grip and stock went off without a hitch. If you need to know what screws to get for the stock, they are 10x1.25" wood screws I got from Lowes. I made sure to get the ones with the slot head to keep 'original' looks, and painted the heads black. Went from this: To this: And with the scope: I like it a bunch and can even store my cleaning capsule in the butt. I didn't think I was going to be a fan of the plumb, but it really looks good. Edited December 21, 2010 by toshbar Quote Link to post Share on other sites
Wade Pruetz 103 Posted December 21, 2010 Report Share Posted December 21, 2010 Looks good please get rid of that pistol grip for a plumb one. 2 Quote Link to post Share on other sites
MN.9130 44 Posted December 21, 2010 Report Share Posted December 21, 2010 Seconded... not a fan of the pistol grip, which is a shame because I AM a fan of the rest of the rifle. Great work! 1 Quote Link to post Share on other sites
toshbar 36 Posted December 21, 2010 Author Report Share Posted December 21, 2010 What???? No likey for the pistol grip? I like it. Quote Link to post Share on other sites
whitetrashrn 74 Posted December 21, 2010 Report Share Posted December 21, 2010 Great job.. I like the salmon grip as well. Quote Link to post Share on other sites
WildmamWilliams 51 Posted December 21, 2010 Report Share Posted December 21, 2010 The grip, maybe not, but hell, you'll be holding it when you use it anyways. The rifle looks great! Love the plum. ALMOST as good as wood IMO. Quote Link to post Share on other sites
Paulry 50 Posted December 21, 2010 Report Share Posted December 21, 2010 I like it, I have the same components and would do it to mine, but for 922r compliance! Quote Link to post Share on other sites
toshbar 36 Posted December 21, 2010 Author Report Share Posted December 21, 2010 (edited) I like it, I have the same components and would do it to mine, but for 922r compliance! That reminds me - I need to go make sure my stamp set is where I left it. Post #123 W00T Edited December 21, 2010 by toshbar Quote Link to post Share on other sites
storm1 2 Posted December 23, 2010 Report Share Posted December 23, 2010 where do you get the salmon pistol grip Quote Link to post Share on other sites
scattergun10 125 Posted December 23, 2010 Report Share Posted December 23, 2010 (edited) Nice job,looks great. Now,you just need to swap out that hideous PG for a Hogue AK grip.(you're welcome) You'll have to settle for black though,they don't make them in plumb. Edited December 23, 2010 by scattergun10 Quote Link to post Share on other sites
Paulry 50 Posted December 23, 2010 Report Share Posted December 23, 2010 How did you get the lower HG retainer on without pulling FSB and GB? Did you split it? Close up photo to show results? This could be huge as I had to buy the modded clamp style to fit my K-Var Stuff! I like the look and have you tried it with the scope on it? Would like to know how yours groups at 100 yards. Frosty Quote Link to post Share on other sites
toshbar 36 Posted December 23, 2010 Author Report Share Posted December 23, 2010 where do you get the salmon pistol grip Got it from APEX gun parts out of colorado. It came with the pistol grip, the front upper and lower handguard and the stock, which does have the butthole for the cleaning kit. It's listed as Bulgarian AK74 polymer stock set and is $45. They have a wood set for $25. I got an East German AKM gas tube from the same site for $30 but now they've taken it off the website. Quote Link to post Share on other sites
essohbe 47 Posted December 23, 2010 Report Share Posted December 23, 2010 I like plum. I happened to have black stuff so I used black on mine but in the future I might swap it out. That's the Brownells retainer isn't it? You didn't have to file the threads? Are you gon'na put a threaded FSB on? Quote Link to post Share on other sites
toshbar 36 Posted December 23, 2010 Author Report Share Posted December 23, 2010 How did you get the lower HG retainer on without pulling FSB and GB? Did you split it? Close up photo to show results? This could be huge as I had to buy the modded clamp style to fit my K-Var Stuff! I like the look and have you tried it with the scope on it? Would like to know how yours groups at 100 yards. Frosty I bought the bolt on retainer from brownells. It was $23 and kalashniklown and I have had good results using it. I've shot it with the scope out to 500 yards where I can pull a 7" group(1.5 MOA) which is fairly good excellent for an AK type gun. Here's a thread you should look at: http://forum.saiga-12.com/index.php?showtopic=59620 I like plum. I happened to have black stuff so I used black on mine but in the future I might swap it out. That's the Brownells retainer isn't it? You didn't have to file the threads? Are you gon'na put a threaded FSB on? yep, brownells retainer. I didn't file the threads on the allen bolt. I doubt i'm going to do the FSB, but i'll leave that open for the future. I have a lot of other things I wanna do with my other rifles right now.(aperture sights, more ammo, NM sights on the AR), Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.