Jump to content

L5K

Member
  • Content count

    588
  • Joined

  • Last visited

  • Days Won

    1

L5K last won the day on May 16 2011

L5K had the most liked content!

Community Reputation

162 Good

About L5K

  • Rank
    Executive Member
  • Birthday 05/02/1986

Profile Information

  • Gender
    Male
  • Location
    Des Moines, Iowa
  1. Gimme a bit. I'll get you squared away. Also, what file type do you need? I'll have to work on it later tonight though. Have to work now.
  2. I have heard nothing but good things about the Primary Arms Microdot.
  3. My next firearm purchase will be a Draco. I'm planning on turning it into a rifle, then SBRing it if Iowa ever allows NFA, or I move to a state that does.
  4. L5K

    new conversion (disconnector problem)

    It looks to me like you might have some burr, or burrs on the mating surfaces of the disconnector and hammer. I'd start there. Also, just to be sure check to make sure the rear upper part of the trigger is not rubbing against the pistol grip. I have had that issue with some new pistol grips needing to be trimmed to clear the trigger and let it reset forward.
  5. L5K

    G36 Rifle Kit

    I don't know what all is involved in actually assembling these parts into a rifle, but at those prices I would definitely be interested in trying to swing it.
  6. L5K

    Basic Conversion Done. Whats Next?

    Remove front sight block, remove gas block, press on the 45 degree one, line it up properly and pin it into position. Be warned they can be a huge pain to get far enough onto the barrel without a press.
  7. L5K

    Vepr X54R/PSL

    I really want one of these VEPRs in x54r.
  8. L5K

    Basic Conversion Done. Whats Next?

    Which AK are you going for here? Since that's a 7.62, I'd say a 45 degree gas block with bayonet lugs, an AKM front sight block, threaded 14x1mm left hand muzzle and a cleaning rod.
  9. L5K

    vented gastube

    All of those I have ever seen are Chinese made. I have one and it will fit a Saiga. It might be slightly loose so you will have to make sure to reuse the spring from your existing gas tube on the rear of it. For your 922r however, the gas tube does not matter one bit. It is not counted as a part for 922r purposes. This setup will, however, cause your handguards to be considered foreign made. As a Chinese upper handguard + a US lower handguard does not count as a US handguard.
  10. L5K

    Saiga IZ-240 5.45 FSB

    It's a US made copy of a Bulgarian or Russian sight block. You do not want it though. It will probably work, but I would never send any of my money to Blackthorne/Hesse/Vulcan Arms. With their parts you get what you pay for, if you even get it. There is a reason they have had to change their name so many times.
  11. It is completely normal for a piston to wobble in an AK. Sometimes they take forever to loosen up, and other times they start wobbling very early. Either way, it's nothing to worry about, it will eventually wobble in any AK.
  12. I don't like Tapco's magazines, but that color is awesome looking in my opinion.
  13. Don't they know they'd make a lot more money selling those toys out to civilians here?
  14. L5K

    Interchangeability saiga 5.45 vs ak74

    Saiga bolts and carriers are AK100 only as far as I have ever heard. The gas piston is an AK100 piston, but I have an AK74 piston in mine and it works, just make sure you get the length correct. Trigger, hammer, disconnector, furniture, and magazine latch stuff is all good to go from any AKM/AK74/AK100
  15. The stock entered the country as a stock. Therefore no matter what you do to it, it will be a foreign made stock. The only way to convert a foreign made part into a US made part is to change what the part itself is. You cannot turn a foreign stock into a US made stock. You can turn a foreign chunk of wood into a US made stock because it did not enter the country as a stock.
×