mpdfish

I want to get my 20 to run on Federal bird shot. I have 3 holes that I can see. I want to enlarge the holes or open up the gas block hole if some are covered. Has anyone done this yet that can help me. Well I pulled the trigger and pulled gas block off (It came off easy!). I have 3 holes which ate approximately 1/16. Any suggestions one how much bigger to make them? My gun cycles slugs but does not kick the shell out on the bird shot. The case usually ends up getting crushed by the feed hood

I have a R&R Burris mount if that's something you are thinking about

OK I read the sticky. I guess I should've been more specific and stating what are my options as far as aftermarket parts without disassembling the gun. If I do decide to disassemble the gun Are Saiga 20 gas holes the same diameter as the 12's?

I know this would be better placed in the Saiga-20 section, but I think this would apply to both guns and this forum gets more traffic. I recently purchased a Saiga-20. I took it out today and it will feed pheasant loads on setting 2. On setting 2 with low base rounds it will fire and load new round but the trigger will not be reset or it will fire and only partially eject the spent case (stovepipe) which is usually the case. What is the best place to start to get this gun running correctly.

I have a R and R mag well. Which limits what I can use

I have been away for awhile and went to my local gun shop and they had a Arsenal converted Saiga-12 for $1050.00. I thought that sounded like a great deal. I go to some of the gun auction sites and they are not even selling for $1000.00. What have I missed.

I have one and have used it for many matches. It is an awesome set up. The other plus is the mag release bar extends toward the trigger so as soon as the gun goes empty you reach up with your trigger finger and tap the release while grabbing your next mag. I would definately recommend it.

I want a free conversion. I am sitting around with the wife and probably drinking a few beers. I did buy $30.00 worth of fireworks which is about 6 here.

Hawktech arms has one for 208 with mount. I think the website is hawktecharms.com

I'm in! Although I will have to figure out how to use it left handed

Burris fasfire

Running an auto plug in MGM Ironman as we speak with no hiccups yet. Shot slugs, shot and 00

I need belt clip for 12 round mag if u can bring it

No just want to know

With some recent topics on op rod length I decided to measure a few things regarding the CSS puc. Here is what is confusing the crap out of me. I took out my gas plug and noticed the CSS puc is just short of the gas holes. I then removed it and put my factory plug in and it sat further back. I then took them both out and measured them. The CSS puck is shorter in overall length! How the hell is that possible?

Im confused...CSS makes a puc that has a nipple that pushes the puc further toward the gas holes and it is supposed to be an improvement. Yet you guys are stating a longer op rod is bad. Why is it okay to lengthen the puc but not the op rod?

Does the piston rod connected to the bolt touch the puck prior to cycling or does the puck slam into the rod? I have a CSS puck and was trying to figure out how the dimple on it helps

I was really looking at one of these...what is the verdict? I think it would be nice to not have to adjust when going from bird shot to slugs and 00 buck.

Is there any info on what exactly all the tools are for that come with your Saiga. I cant figure out what the screwdriver looking thing is for and what exactly all the holes in the carrying tube do.

The magwell and brake may be an R&R Racing gun.

I want a picatianny rail for a dot sight. I dont think I need all the rail space on the sides and bottom of handguard. My assumption is the UTG handguard would make the dot sit higher and the foregrip alot wider than the Ultimak rail and a CSS handguard (non railed). Please make a recommendation on which one and why.

I will be there on Primary Weapons Systems squad. Hopefully my Saiga will be completed and get to me in time to use it (on the way from Tromix)....I would love to show it off.

Winchester AA or Remington Nitro- 2 3/4

It would be great if you could give me that info

I hear alot of people stating not to use low base shells for the Saiga, however I want to reload 00 buck for my Saiga 12 and was wondering if low base hulls applied to 00 buck. Thanks in advance.