ramlake

Russian / Bulgarian or build your own.......billet w/steel and aluminum tubes, and extra beefy hinge I built these for my personal 8" s12's It took a lot of time.

Hard chrome

Did you make that plate? The one at CSS is a straight rectangle without the notch. Yes, but the vendors plate can be fitted. By recessing the plate flush to the reciever you can really penetrate into the thicker tang area and create a really strong weld.

Just be careful cause your probably not going to be happy with a muffler shops weld on that rear plate!

A good welder won't roll the bead over the edge of the reciever then grind and grind till the ends are rounded and without definition. Ask the welder what weld prep for the plate is needed for good penetration You can see a 45 degree all around the plate. And don't forget about the buttstock angle you prefer. I like parallel with the bottom of the reciever, some like parallel with the barrel. finished with plenty of penetration especially around the tang area for strength. Crisp edges, a factory look.

After building a dozen or so 8" s12's for my personal collection I've only built 2 SBS's without relocating the gas system These are 14.5" length barrels and they did need work to cycle bulk pack WallMarx ammo Even cutting 1" usually creates the need to tune http://www.youtube.com/watch?v=0RcRyhtrLl8

cut it down to 13 inches, with that length you won't have to screw around with making the gas port larger.......Do What?

Izhmash magwell and molot magwell yes. Does exist for quite some time already. Magwell drums as well as a conversation kits. Not sure about other magwells. yep but for the Maxround / AA drum It can be done for the MD20 but definitly not for sale

I have done several of my own with removable gas tube and handguard. Although dinzags does not have lever release gas tube it's absolutly worth every penny as far as labor and material cost

Add your own

I have 21 saiga 12's and 20 of them have 4 ports at .073....this includes many SBS's Going too big invites fouling issues

No need to remove barrel Use an expandable collet or turn soft jaws, grab it by the I.D, and use a steady rest. Make a light qualifing pass end and then hold it on the O.D with 3 jaw. Turn the barrel back for the gas block then part off at the desired length. Setup on the I.D again and thread so the bore and threads will be concentric. http://www.youtube.com/watch?v=FpHDwXN1hnk Many of the forum business members can easily do this for you also.

That's cool Mine also slips in exactly as the stock gas tube block does but to keep it from cantilevering up at the front I tiged a small fillet on thr trunuin just as legion does. There are several popular legion modls that they just set the modified AK RSB on top of the barrel and weld on thr existing gas block Factory Mine

Welding to trunuin is an acceptable method. Legion has been doing it for years on dozens of models. All of the new legion models with AK RSB's, including the Iz433 / 030 for example use this method also. I'm not sure on Superhawk138's I had to build my own for my own projects.

I have seen your work before superhawk138 and I am very impressed! You wanted it bad enough and you did it, lookin Good!

What length barrel?

It is.........Mine!! I talked with Max a couple of years ago and he said he was not sure where it came from. The Russians have built sooo many variants it's hard to say. I like it a Loooot

Adjust your monitor, they are there. The home page 12" has lower rivets? Maybe I need to get my eyes checked. I think I see, you are talking about the lower rear trunuin rivet on the right shown side. Looks to me that pic is pretty well doctored up as is, who knows?

Adjust your monitor, they are there.

Well finally got video of testing

Seems the redjacket is being tested first with standard loads, or even heavy loads ( look at ejection) then low recoil loads with the suppressor. The CGW looks like the same ammo used in both tests. What I don't understand is why the industry standard Bruel & Kjær 2209 meter is not used to give more accurate levels for these products. Different loads, even in the same test, and different camera's, shooting in different angles I feel is really misleading .

I have always shot shotties at CE ?, last time 4 months ago, going back this saturday.

I shoot at bulleye quite a bit. Let me know next time you go. Charlie Eliott game ranch is good also. Good lookin saiga's make me green with envy!!

You can't just send in a letter, you have to send in the device to the tech branch for evaluation. how do I know? The BATF has had mine for 6 months....any day now. Cool. Let us know how it turns out. And I do like what you said above post-apocalyptic, acually very wise! One should be careful about things others don't understand. Just be careful and well informed. Even if it functions exactly like approved existing models? i.e. the ones Csspecs and others made. As near as I could tell, the only thing unique to other prior desingns on the slide fire models, is the fi

http://www.midwayusa.com/product/944110478/boyt-thompson-center-contender-case-21-x-10-canvas pro's 21" heavy duty cons no dividers or straps perfect for 8" saiga