papa_celms 2 Posted January 15, 2013 Report Share Posted January 15, 2013 (edited) Hey everyone I've been a lurker on this site since I ordered my vepr 12 a month ago. I finally received my vepr 12 yesterday and today I took it out for a spin. I ran a 10rnd sgm mag a 12rnd sgm mag and the factory mag. The factory mag worked great but the sgm mags did nothing but jam, and fall out of the bottom of the gun after evey shot. I looked up reviews on the sgm mags and saw nothing but praise anyone else have any issues, any thoughts. I also noticed that the mags are considerably harder to get into the gun than the factory(they catch on the gun inside the mag well), but I believe that its because they have sharp edges instead of rounder ones like the factory. I made sure they were inserted in the gun. I stuck em in and yanked on em to verify. HMM found this still reading through it. http://forum.saiga-12.com/index.php?/topic/82964-sgm-12-round-mag-falling-out/ Edited January 15, 2013 by papa_celms Quote Link to post Share on other sites
physicsnerd 139 Posted January 15, 2013 Report Share Posted January 15, 2013 Not sure what to tell you but here is a slight aside. My first two SGM 12s for the Vepr had mag bodies that narrowed too much towards the top. From the time that I sent them in to the time that I got them back was 1 week. So if you have some issues SGM is very willing to help you out. The replacements I broke in by hand by loading and unloading them until the rounds would no longer stick. My final test was to cycle them manually (vigorously) through the action which they did without failing. Needless to say, if I have more issue I have no doubt that SGM will help me out. Drop them an email if you're not satisfied. Quote Link to post Share on other sites
papa_celms 2 Posted January 15, 2013 Author Report Share Posted January 15, 2013 Took it out again really waked on the bottom of the mag with my palm. Still isn't catching properly. After looking over the mag it appears that the mag catch on the gun is just barely catching the lip of the mag what would the best rout in breaking it in be without putting a file to it. I don't want to void my warranty. Quote Link to post Share on other sites
chevyman097 2,579 Posted January 15, 2013 Report Share Posted January 15, 2013 just keep working it in and out and it will break it. Quote Link to post Share on other sites
menace667 194 Posted January 16, 2013 Report Share Posted January 16, 2013 To elaborate on chevy's post, SGM stated that all their mags are from the same mold so they are all identical. Differences in the guns would be the only variable in accounting for any fit issues. They then continued by recommending to hand load a few times and then load and eject the magazine a few times to make it fit to your specific firearm better. They do have excellent customer service and will take good care of any issues you have. Quote Link to post Share on other sites
TheGreenPotato 0 Posted January 16, 2013 Report Share Posted January 16, 2013 Hmm, I order two of these two days ago :| Quote Link to post Share on other sites
papa_celms 2 Posted January 19, 2013 Author Report Share Posted January 19, 2013 well I'm at a loss. The only think I can see is that when I insert the factory magazine, the mag clip on the shotgun makes contact against the outside wall of the magazine itself. (Fully covering the magazine tab.) When I insert the SGM magazine any of the 4 different SGM magazines I bought, The guns magazine locking clip only covers about half the SGM magazine catch tab. Another thing I've discovered is that If I hold the magazine eject button shut the magazine stays in the gun, instead of falling out after each shot. Only did this 1 or 2 times so i haven't tested this extensively, but The SGM magazine ALLWAYS falls out after each shot. Quote Link to post Share on other sites
evlblkwpnz 3,418 Posted January 19, 2013 Report Share Posted January 19, 2013 It sounds like the tab needs to be fitted a very little bit. A couple of strokes with a precision file on the tab should do it. They can either make them fit all weapons easily and some weapons sloppily, or they can make them where they may need slight fitting. I would rather fit the mags than have them fit loosely. Quote Link to post Share on other sites
papa_celms 2 Posted January 19, 2013 Author Report Share Posted January 19, 2013 (edited) I tried to get some pictures of the veprs magazine tab covering the sgm tab but the camera couldn't get take a decent picture through such a small hole. This is what I could get though. I'm afraid ill have to modify the vepr magazine release switch so that the catch portion can grab the sgm mags better. Factory Magazine SGM Magazine Edited January 19, 2013 by papa_celms Quote Link to post Share on other sites
chevyman097 2,579 Posted January 19, 2013 Report Share Posted January 19, 2013 I would NOT take the chance at messing with the tab on the gun. imo 1 Quote Link to post Share on other sites
ec4321 113 Posted January 19, 2013 Report Share Posted January 19, 2013 You can get an aftermarket mag catch latch from CSS et al. You can work on the aftermarket one to fit it if you're worried about your factory stock one. Quote Link to post Share on other sites
Aries144 10 Posted January 19, 2013 Report Share Posted January 19, 2013 (edited) I'm guessing the SGM mags were made over sized compared to the factory mags. Since the factory mag works fine and the SGM mags are over sized in other dimensions, I'd file on the SGM mags first or consider getting an aftermarket catch to play with. If you file the catch much, it's likely the factory mags won't fit right. Edited January 19, 2013 by Aries144 Quote Link to post Share on other sites
papa_celms 2 Posted January 19, 2013 Author Report Share Posted January 19, 2013 snaps think i soiled my pants a little lol $30 for a mag catch. I'll have to take a look at my sgm mags. Seems I need to get the magazine closer to the mag catch. Any suggestions are welcome. Quote Link to post Share on other sites
papa_celms 2 Posted January 23, 2013 Author Report Share Posted January 23, 2013 Well I ordered a regular saga 12 magazine latch I'll let you all know how it goes when I get it in. Quote Link to post Share on other sites
Sigurd 3 Posted January 28, 2013 Report Share Posted January 28, 2013 I too am having extreme difficulty fitting my new SGM mags into the magwell. All my factory mags fit fine. Where should I file? I have tried to email SGM and received no response regarding this. Also, I never received my hi-cap for preordering the Vepr. Who should I contact re this? MAA or SGM. Quote Link to post Share on other sites
Dr Robert Neville 6 Posted January 28, 2013 Report Share Posted January 28, 2013 Ditto here, the SGM mags are not fitting as well as the Molot mag. I have another V12 enroute and will try the SGM mags in that gun before I contact SGM. I need to shoot a bunch of rounds through the SGMs before I get too excited. The good news is no FTEs (yet) Quote Link to post Share on other sites
papa_celms 2 Posted February 3, 2013 Author Report Share Posted February 3, 2013 (edited) Alright I Fixed it sucessfully, and figured out how to install the spring fairly easily took around an hr and a half to figure out how to get the spring in correctly and damaged one, but now that I know how to do it easy pezy. If your magazine catch isn't grabbing the mag fully its because the ramp on the veprs magazine catch isn't filed down enough. I'm thinking about making a tut vid if there's support for it. Anyway I'm using a saga 12 mag catch for reference since mines in my gun but you need to file here. Its helpful to file and put the pin in without the spring then manually latch the pin, peer down the mag catch hole and see where it grabs. I have mine catch the mag nearly to the body of the magazine. Edited February 3, 2013 by papa_celms Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.