Cobra 76 two 2,677 Posted September 16, 2010 Report Share Posted September 16, 2010 Ok so there I was...doing a really simple task (well not as simple as it is on my Mustangs)...changing the spark plugs on Racegal's 93 Blazer with the Vortec V-6. Of course, I was almost done getting them all out, down to the second to last of 6. Then it happened....what you always hope won't happen when working on an old rustbucket from up north....what felt like the spark plug breaking free was actually the damned thing breaking in half! DAMMIT! Here's what I got... As Johnboy says...NOT Too Good! Argghhhh! Tried this... And this... And this... And still I have this... Has anyone ever used an impact wrench on an easy out? That sucka aint budging with the regular ol 1/2" drive breaker bar and iron pipe extension. Not much room to work in that wheel well either...even after I finally coaxed the wheel off... I don't know if that EZ out can take the torque and pressure of my impact wrench..or can it? I sure as hell don't want to break that mother off in there too. Damn I don't wanna have to pull that f&@kin head because of this shit! Any of you guys ever had this happen before? Quote Link to post Share on other sites
gregomega 929 Posted September 16, 2010 Report Share Posted September 16, 2010 Ok so there I was...doing a really simple task (well not as simple as it is on my Mustangs)...changing the spark plugs on Racegal's 93 Blazer with the Vortec V-6. Of course, I was almost done getting them all out, down to the second to last of 6. Then it happened....what you always hope won't happen when working on an old rustbucket from up north....what felt like the spark plug breaking free was actually the damned thing breaking in half! DAMMIT! Here's what I got... As Johnboy says...NOT Too Good! Argghhhh! Tried this... And this... And this... And still I have this... Has anyone ever used an impact wrench on an easy out? That sucka aint budging with the regular ol 1/2" drive breaker bar and iron pipe extension. Not much room to work in that wheel well either...even after I finally coaxed the wheel off... I don't know if that EZ out can take the torque and pressure of my impact wrench..or can it? I sure as hell don't want to break that mother off in there too. Damn I don't wanna have to pull that f&@kin head because of this shit! Any of you guys ever had this happen before? Damn, That sucks. Ill get back to you on that, my girl's dad is a tech and has been working on vehicles forever. Ill ask him when I go over there after work here in 5min. maybe he'll be able to help. Good luck in the mean while. Quote Link to post Share on other sites
Nailbomb 10,221 Posted September 17, 2010 Report Share Posted September 17, 2010 Do you have a mig gun? You can weld a bolt to the remaining piece and then soak it in more oil. this gives you more to grab ahold of, applies heat, and penetrating lubricant all at the same time. Quote Link to post Share on other sites
Nailbomb 10,221 Posted September 17, 2010 Report Share Posted September 17, 2010 Oh and do make sure you use caution. you don't want to welt the threads to the head, just the bolt... Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 Mmmmmm nope, unfortunately not. I've read about people actually using superglue with success (no really! LOL!) but I don't have much confidence in that. There's just not much of a metal on metal contact area left where it broke off. This was an interesting thread I found on a Ford forum...similar sounding situation.... http://www.ford-trucks.com/forums/44739-help-with-broken-spark-plug.html 1 Quote Link to post Share on other sites
Nailbomb 10,221 Posted September 17, 2010 Report Share Posted September 17, 2010 Soak it every day for a few days. of course this takes time and patience, I'm not good at either. Quote Link to post Share on other sites
nycGUNguy 61 Posted September 17, 2010 Report Share Posted September 17, 2010 Try reinserting the spark plug then tack welding it in 2-3 places (MIG) then try to get it out. Using the impact gun on the easyout might break it or send shavings into the head. Maybe if you put a shopvac at same time as trying to drill it out...maybe. Good luck, whatever you do and let us know what happened. nyclu3 Quote Link to post Share on other sites
Nailbomb 10,221 Posted September 17, 2010 Report Share Posted September 17, 2010 have you cooked the fuck out of it with the torch and tried the extractor when its still cherry? Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 I wasn't able to really get it that hot with that torch. Maybe tomorrow I'll take the Oxy Acetylene torch to it. Quote Link to post Share on other sites
geepelton 105 Posted September 17, 2010 Report Share Posted September 17, 2010 Get a helicoil kit for any local parts store. I have done it many time and it works great. Quote Link to post Share on other sites
Makc 64 Posted September 17, 2010 Report Share Posted September 17, 2010 …this project is dramatically lacking the proper amount of beer! I mean, there is only one darn can in all of the pictures!!! NEED MORE BEER!!! Quote Link to post Share on other sites
Marc 147 Posted September 17, 2010 Report Share Posted September 17, 2010 tap the hole with a left handed tap, thread in our flavor of left handed bolts and torque it down until the right handed threads come loose. if that don't work, drill out the old plug and chase the threads with the proper sized drill/tap combo. it that don't work, drill out the and tap the hole to fit the next oversize spark plug. use a mini-vac and air compressor to clear chips out of the cylinder. Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 Hmmm some really good suggestions coming out. LOL@ MAkc hahahaha! I'm workin on that now Max, while watching my hometown Wolfpack kick some ass on ESPN! Woooooo! Actually there were at least 4 dead soldiers down there when I finally said fuggit and came up to the house to run this past you guys. Thanks for all the help so far! Rangerguy what's a helicoil? Need to google that I guess. Quote Link to post Share on other sites
VaiFanatic90 360 Posted September 17, 2010 Report Share Posted September 17, 2010 tap the hole with a left handed tap, thread in our flavor of left handed bolts and torque it down until the right handed threads come loose. if that don't work, drill out the old plug and chase the threads with the proper sized drill/tap combo. it that don't work, drill out the and tap the hole to fit the next oversize spark plug. use a mini-vac and air compressor to clear chips out of the cylinder. I was gonna suggest using a left-handed tap, but I figured it may have been a bit far-fetched. But now that someone else has suggested it, I have someone else to agree with. I'd give it a try if you've got the tools. Good luck, Cobra. Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 That LH tap is sounding the most doable to me at this point...if I can get in there and get it tapped in those cramped quarters... At least the one plug that broke was the easiest to get to. Now I guess I need to soak the crap out of it for a few days like Jake said, while I try and find one of those taps. Still need to investigate the helicoil too.... Hey Rangerguy! Don't you wanna come up sometime this weekend and blow some shit up?? lol! Quote Link to post Share on other sites
RobRez 1,895 Posted September 17, 2010 Report Share Posted September 17, 2010 Have you tried this?.... Quote Link to post Share on other sites
gregomega 929 Posted September 17, 2010 Report Share Posted September 17, 2010 Ok so there I was...doing a really simple task (well not as simple as it is on my Mustangs)...changing the spark plugs on Racegal's 93 Blazer with the Vortec V-6. Of course, I was almost done getting them all out, down to the second to last of 6. Then it happened....what you always hope won't happen when working on an old rustbucket from up north....what felt like the spark plug breaking free was actually the damned thing breaking in half! DAMMIT! Here's what I got... As Johnboy says...NOT Too Good! Argghhhh! Tried this... And this... And this... And still I have this... Has anyone ever used an impact wrench on an easy out? That sucka aint budging with the regular ol 1/2" drive breaker bar and iron pipe extension. Not much room to work in that wheel well either...even after I finally coaxed the wheel off... I don't know if that EZ out can take the torque and pressure of my impact wrench..or can it? I sure as hell don't want to break that mother off in there too. Damn I don't wanna have to pull that f&@kin head because of this shit! Any of you guys ever had this happen before? Pleanty of people have already suggested plenty of possible solutions, but I asked and he said no impact wrench. You'll more than likely brake it. Some help I was, well good luck anyway Quote Link to post Share on other sites
geepelton 105 Posted September 17, 2010 Report Share Posted September 17, 2010 Man I would love to come blow some shit up. I just started working again so I'll be on the road for the next two or three months. I will defiantly let you know when I get get back so we can do some shooting. Quote Link to post Share on other sites
308SAIGA 55 Posted September 17, 2010 Report Share Posted September 17, 2010 tap the hole with a left handed tap, thread in our flavor of left handed bolts and torque it down until the right handed threads come loose. if that don't work, drill out the old plug and chase the threads with the proper sized drill/tap combo. it that don't work, drill out the and tap the hole to fit the next oversize spark plug. use a mini-vac and air compressor to clear chips out of the cylinder. I for one would not use this method, I would fear shavings would enter the cylinder and screw up more then what it is worth..... I like the Mig idea... Quote Link to post Share on other sites
geepelton 105 Posted September 17, 2010 Report Share Posted September 17, 2010 If you bring the piston all the way up, drill it, stick a magnet in the hole to get the big chunks out, blow it out with compressed air, start the engine with the plug not in there for a few seconds. You will be fine. I have done this a couple of times. The big chunks are what you have to worry about. Quote Link to post Share on other sites
bigcec1 72 Posted September 17, 2010 Report Share Posted September 17, 2010 A heli coil is basicly a rethreading kit you drill the hole out larger and you insert this coil that is the new threads I have done a few and they work great http://www.youtube.com/watch?v=RFYa6sjhh_E And Snap on makes a broken spark plug removal kit but unless you do it all the time its not worth the cost is mainly for ford triton 5.4l and 4.6l motors and have used it on outhers works great but for a cheap way to do it the left hand tap and bolt works great in a pinch Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 Thanks everyone for their input. I appreciate it. I was hoping there was some kind of magic bullet people commonly use when this happens. I figured my luck couldn't be quite bad enough that it was that rare to snap one off like this. Boy isn't now one of those times I wish all had to deal with was a pissant little broken tap in bullet guide...lol! This friggin sucks royally. I'm just glad it was the only plug that I can actually get straight on to work with the bastard. Mig welding is not an option for me at this time, so getting it out like it is will be my plan of action. Soaking it good for a few days by coating it good with KROIL, Liquid Wrench, Marvel Mystery Oil, or PB Blaster (or maybe all of em...lol) and soaking a rag with it and stuffing it in there, then covering with plastic to keep it from evaporating, might help loosen it some...maybe... This truck is the rustiest mofo I think I've ever seen. It must have spent most of it's life totin fenderburgs around most of the year on salty roads....lol. I literally had to beat the wheel off of it even (an aluminum rim) with an 18 lb sledge hammer and block of wood....AFTER soaking it with PB for awhile. It wouldn't even budge after I took the lug nuts off. I bet those threads are almost welded to the head with rust, being where is next to the wheel well. Been PMing with Rangerguy some and he and I both think it's prolly best to just drill it out til I can get really close to the threads, then try and pry it loose by driving a center punch in there and try to bend it inward. If all else fails just drill the whole damn thing out and use those helicoils to put new threads back for the plug. Man...what a bitch! How can such a simple ass little job like changing the plugs turn into such a PITA. I guess I can look forward to cutting the damn oil filter off as well...oh wait! It's been lubed all it's life! Quote Link to post Share on other sites
Cobra 76 two 2,677 Posted September 17, 2010 Author Report Share Posted September 17, 2010 That said, if I can find a LH tap somewhere for not too much, I'd be willing to give that a try too after soaking it for awhile. Should I get fine or coarse threaded? Which would be easier to tap. It's gonna be a bitch to get in there to it. I'll have to rig some kind of straight extension to turn the tap with. Also does anyone know offhand, what the thread size for spark plugs is on a chevy V-6 head? I'll need another tap to chase the factory threads with once I get it out. I may actually have that,but not the LH one. I'm guessing I'll prolly want about a 1/2" or a little smaller for the LH one. Also, Racegal's son is a NASCAR Tech grad, who won a few grand worth of automotive tools from Snapon when he graduated. He may have something I need... Thanks again for all the help guys. 1 Quote Link to post Share on other sites
geepelton 105 Posted September 17, 2010 Report Share Posted September 17, 2010 A left hand drill bit might work too if your going to try and drill it close to the threads. Soak it a while before your do this. Just a thought... Quote Link to post Share on other sites
Spartacus 1,619 Posted September 17, 2010 Report Share Posted September 17, 2010 (edited) I literally had to beat the wheel off of it even (an aluminum rim) with an 18 lb sledge hammer and block of wood....AFTER soaking it with PB for awhile. It wouldn't even budge after I took the lug nuts off. I bet those threads are almost welded to the head with rust, being where is next to the wheel well. I had a '75 Grand Prix (loved that car) where the wheels would stick like that. Found out the trick is to loosen all of the lug nuts and then run the car back & forth a few times hitting the brakes hard. That cracks 'em loose. Good luck on the fubar plug. Edit: Should have added to only do one stuck wheel at a time this way and make sure the lug nuts are almost to where they would tighten against the wheel (not just hanging by the last thread on the stud). This method does work well for stuck/seized on wheels. Edited September 17, 2010 by Spartacus Quote Link to post Share on other sites
Nailbomb 10,221 Posted September 17, 2010 Report Share Posted September 17, 2010 I would stick to the kroil. I live well into the rust belt, and syracuse is the salt city for a reason. Kroil has to be the best penetrating oil i've found for dealing with a claped out rustbucket I've ever seen. Quote Link to post Share on other sites
BronCobraJet 80 Posted September 17, 2010 Report Share Posted September 17, 2010 I have also read to heat it cherry hot, then apply candle wax. it will seep into the threads easier than penetrating oil. My 87 Sbuburban was a nightmare to get the original plugs out of last year, but thankfully, none of them broke. When you put the new plugs in - ANTI-SIEZE! I use it on absolutely everything anymore. I had no problems pulling the plugs and most of the fastners on my 67 Coronet. They just keep using cheaper hardware as every year passes. (my burban looked about as rusty as your pics), but just on the engine and outer body. lol. Try the candle wax, what do you have to lose? It's been an old staple for awhile. 1 Quote Link to post Share on other sites
Stansplace 414 Posted September 17, 2010 Report Share Posted September 17, 2010 Tap (knock the hell out of it) on what's left with an aluminum bar and hammer as well. It will break the rust apart and free up the threads. 1 Quote Link to post Share on other sites
scoutjoe 276 Posted September 17, 2010 Report Share Posted September 17, 2010 Shannon my car would scare you with the amount of rust....guess I shouldn't drive it to work plowing snow as I go Penetrating oil, heat, more oil, repeat till free (just don't beat the hell outta it) Quote Link to post Share on other sites
Marc 147 Posted September 17, 2010 Report Share Posted September 17, 2010 That said, if I can find a LH tap somewhere for not too much, I'd be willing to give that a try too after soaking it for awhile. Should I get fine or coarse threaded? Which would be easier to tap. It's gonna be a bitch to get in there to it. I'll have to rig some kind of straight extension to turn the tap with. Also does anyone know offhand, what the thread size for spark plugs is on a chevy V-6 head? I'll need another tap to chase the factory threads with once I get it out. I may actually have that,but not the LH one. I'm guessing I'll prolly want about a 1/2" or a little smaller for the LH one. Also, Racegal's son is a NASCAR Tech grad, who won a few grand worth of automotive tools from Snapon when he graduated. He may have something I need... Thanks again for all the help guys. Any machine shop supplier, specialty bolt store or any REAL hardware store should have your LH tap which shouldn't cost any more then a right handed tap. I'm not sure that a fine or coarse thread will make much difference, although a fine thread may be easier to get started straight in your situation. I would measure the hole you have then drill it out to the next available tap size, that way you get a good clean hole to tap and make strong threads to torque on. Good luck. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.