number1punk 17 Posted July 27, 2010 Report Share Posted July 27, 2010 1)does anyone have a measurement of how much material to remove from the sleeve on my G2 hammer to clear the BHO lever? 2)am i correct in assuming i only have to shave down the side adjacent to the BHO? Quote Link to post Share on other sites
icefire 10 Posted July 27, 2010 Report Share Posted July 27, 2010 Just grind about the thickness of the BHO plate. And only on that side, yes. The idea is to make room for the thickness of the BHO plate, thats all... I bought mine already modified from Dinzag for about $5 more, he also polishes up all the ares that need it. Its like getting a trigger job for free.. 1 Quote Link to post Share on other sites
Avtomat 3 Posted July 27, 2010 Report Share Posted July 27, 2010 Just grind about the thickness of the BHO plate. And only on that side, yes. The idea is to make room for the thickness of the BHO plate, thats all... I bought mine already modified from Dinzag for about $5 more, he also polishes up all the ares that need it. Its like getting a trigger job for free.. +1 !, I bought the same trigger from Brian at Dinzag. Polished very nice and the cut for the BHO lever is very clean and precise. I poslished bolt carrier and bolt where they meet the FCG, vey nice trigger now. Quote Link to post Share on other sites
SJgunguy 5 Posted August 12, 2010 Report Share Posted August 12, 2010 You could hold up the 2 hammers next to each other and remove material until the 2 are the same. 1 Quote Link to post Share on other sites
paprotective 362 Posted August 12, 2010 Report Share Posted August 12, 2010 Usually about 1/8" or so. Thickness of the plate.. I did my 3 conversions myself.. Al Quote Link to post Share on other sites
nalioth 405 Posted August 12, 2010 Report Share Posted August 12, 2010 You don't need the BHO in a rifle (nor in a shotgun, but I am among the minority with that opinion). Throw the BHO away, and weld up the slot - you'll be happier. 60,000,000 soldiers can't be wrong. 2 Quote Link to post Share on other sites
ksjlm09 0 Posted August 12, 2010 Report Share Posted August 12, 2010 I had written down .050". I'm not sure where I got that from but in the end I just compared the new one to the original hammer and ground until they were the same. Quote Link to post Share on other sites
Deussne 38 Posted August 14, 2010 Report Share Posted August 14, 2010 (edited) You don't need the BHO in a rifle (nor in a shotgun, but I am among the minority with that opinion). Throw the BHO away, and weld up the slot - you'll be happier. 60,000,000 soldiers can't be wrong. Some ranges require to have a bolt locked back to show that the rifle is clear. Mine is one of those ranges... Edited August 14, 2010 by Deussne Quote Link to post Share on other sites
Paulyski 2,227 Posted August 14, 2010 Report Share Posted August 14, 2010 You don't need the BHO in a rifle (nor in a shotgun, but I am among the minority with that opinion). Throw the BHO away, and weld up the slot - you'll be happier. 60,000,000 soldiers can't be wrong. Some ranges require to have a bolt locked back to show that the rifle is clear. Mine is one of those ranges... When you are firing fast & not paying attention, you can accidentally hit the BHO & that could cost you your life. There are other options. Cadiz has released an automatic LAST ROUND BHO too. Click the pics. $35.00 $64.95 Its like getting a trigger job for free.. Good answer. But... Why is it that any time anyone says getting a insert "whatever" here job.... It sounds dirty? Quote Link to post Share on other sites
Foxtail207 23 Posted May 26, 2011 Report Share Posted May 26, 2011 I had written down .050". I'm not sure where I got that from but in the end I just compared the new one to the original hammer and ground until they were the same. That comes from he CSS videos. The installer on there says take off .050". Quote Link to post Share on other sites
WhiteRabbit 4 Posted June 29, 2011 Report Share Posted June 29, 2011 You don't need the BHO in a rifle (nor in a shotgun, but I am among the minority with that opinion). Throw the BHO away, and weld up the slot - you'll be happier. 60,000,000 soldiers can't be wrong. I've looked at the internals out of pure idle curiosity and I'm pretty sure there's not enough space for both an autosear and the BHO lever. I like my BHO lever. It's very important to me and I definitely have no intentions of giving it up. Installing the BHO is challenging even after it's ground. I used this video, dental floss and a spoon - tie the spoon or other finger-friendly object to the end of the dental floss to get a better grip. Quote Link to post Share on other sites
bdub 6 Posted July 6, 2011 Report Share Posted July 6, 2011 I purchased the G2 trigger from CSS, which I believe has been ground (they say modified, so that is what I assume). I haven't done my conversion yet, but I have decided that I don't want to install my BHO anymore, do I need a spacer/washer to make up for leaving the BHO out? Quote Link to post Share on other sites
ripcuda 5 Posted July 6, 2011 Report Share Posted July 6, 2011 I purchased the G2 trigger from CSS, which I believe has been ground (they say modified, so that is what I assume). I haven't done my conversion yet, but I have decided that I don't want to install my BHO anymore, do I need a spacer/washer to make up for leaving the BHO out? I'm pretty sure the answer is yes. I just converted my Saiga yesterday also using the CSS kit. Without the BHO lever, the hammer would be able to slide on the pin. Would it? Seeing how the rest of the trigger is pretty fixed side-to-side and would keep the hammer aligned... I'm guessing no. But I think a washer in place of the BHO is a safe bet. I left my BHO in... and didn't like how far down the lever stuck into the trigger finger area. Like others, I pushed the lever all the way up, traced it with a pencil against the receiver and trimmed the BHO lever with a dremel. MUCH better now! I won't notice it until I want to use it. Cheers! Quote Link to post Share on other sites
Bigtwin 219 Posted July 17, 2011 Report Share Posted July 17, 2011 Or for the range rules as somebody mentioned, you could easily grind away the safety lever to work as such. I did so while it was out for conversion. Quote Link to post Share on other sites
pjj342 632 Posted August 6, 2011 Report Share Posted August 6, 2011 Or for the range rules as somebody mentioned, you could easily grind away the safety lever to work as such. I did so while it was out for conversion. Im glad you said that twin, I was going to suggest the same thing. Ive heard that done a few times and will eventually do it myself. Then you can have space for a full auto sear if you need one (most dont). Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.