sonofliberty 6 Posted January 3, 2012 Report Share Posted January 3, 2012 I'm getting ready to lay down the $140 for the Texas Weapon Systems top cover rail setup and I'm wondering about rear sight options. The $40 they want to charge for that dinky little rear peep seems a little insulting and exploitative in my opinion after spending so much on the rail to start with. Personally, I think that such a small part should just be included in the package since it is basically useless as is without the additional purchase of an optic or their peep sight. I'm a little annoyed so I'm looking for other options. I have the Bolton FSGB installed now and it lines up fine with the standard rear sight so I need to find something that sits along that same plane. Every AR BUIS I've seen sits way too high. I intend to mount a scope high enough to retain the use of backup irons underneath. Any thoughts? Quote Link to post Share on other sites
markdavidson 28 Posted January 3, 2012 Report Share Posted January 3, 2012 Capitalism is a wonderful thing, my understanding is, they are getting ready to offer a leaf sight option that replaces the front portion that attaches to the RSB to mimic the AK blade. I would be more interest in that as an iron back-up myself Quote Link to post Share on other sites
Reverendfranz 160 Posted January 3, 2012 Report Share Posted January 3, 2012 Unfortunately, your options are pretty limited, with the standard ak FSB. I bought the TWS for the peep site alone, a longer sight radius is always preferable, and the TWS is nicer than the TechSight, imho. Now, it is a dinky sight, true, but the added height of the rail means anything you put on it is going to be too tall. What i would like to see is a low profile AR or M14 peep sight that bolts up to the rail, and also comes with a replacement, slightly taller AK front sight post. If you can find another sight that is only a couple of MM tall, go for it, but i think you will need a taller front sight post to have anything that really would work. The only alternative i can see would be to somehow mount the sight behind the dustcover, say on the latch so that you could mount its base lower than the factory leaf sight and have room for it to match up with your front sight, but then you are fabing up a new mounting surface, and it might be too close to your eye. Quote Link to post Share on other sites
ViperHummel 3 Posted January 3, 2012 Report Share Posted January 3, 2012 I bought the peep sight. I only used it once b/c when my eotech was on it was rather useless since it is so short. However, without re-zeroing the AK was hitting 10inch steel plates at 100m. I saw a guy on here take his 5.45 saiga and put flip up BUIS on the TWS and the front rail. I asked how they worked out but he hasn't responded. Quote Link to post Share on other sites
Zambidis 90 Posted January 4, 2012 Report Share Posted January 4, 2012 I've been reading about the leaf sight on another forum. I think that if one is using the top rail to mount an optic that will be a much better BUIS. Quote Link to post Share on other sites
Zombiehunter762 376 Posted January 31, 2012 Report Share Posted January 31, 2012 I just installed the TWS Dog Leg Gen II and it fit perfect on my Draco SBR. Mounting a Trijicon TA26R4 compact ACOG which sits low. I get it Wednesday and will throw in a pic and an update. My TA31F was just a little to high, but not much. Quote Link to post Share on other sites
netpackrat 566 Posted February 1, 2012 Report Share Posted February 1, 2012 I have the TWS on my S308 with the peep sight and it is adequate. I have another TWS rail and the new leaf BUIS unit ordered for one of my Romy G builds... Still trying to decide on a red dot for that rifle, but since I was one of the guys who suggested that TWS mill a rear leaf into the dogleg unit, I figured I should probably put my money where my mouth was. Quote Link to post Share on other sites
rs51085 136 Posted February 1, 2012 Report Share Posted February 1, 2012 (edited) I too thought the tws peep sight was to high so I skipped it. I am going to wait for the leaf sight option. I put the tws on my mini and a small fastfire knockoff. I like my setup and it holds zero good. Edited February 1, 2012 by rogers 1 Quote Link to post Share on other sites
Zombiehunter762 376 Posted February 7, 2012 Report Share Posted February 7, 2012 I currenty have a Trijicon ACOG TA26 1.5x16 compact on special ring mount attached on the TWS on my Draco SBR. I also have a Eotech XPS3-0 that I can mount on it also. They both are very excellent. I was thinking of selling the Trijicon ACOG, which is basically new if anyone knows anybody looking for a good deal. Quote Link to post Share on other sites
Zombiehunter762 376 Posted February 7, 2012 Report Share Posted February 7, 2012 Hey Rodgers, How you like your Mini Draco? Any issues with it? What kind of qaud rail did you go with? Your set up looks good. Quote Link to post Share on other sites
rs51085 136 Posted February 15, 2012 Report Share Posted February 15, 2012 Mfwic, I love my mini. The only problem I had with it was the factory hand gaurd would come lose after a few rounds so I put the quad rail on and all is well. The rail is a utg for a regular ak. I had to cut the top rail re tap two holes on the bottom rail for the shorter top rail, drill a hole for the lower handgaurd retainer bolt, and enlarge the end of it for the muzzle brake to fit. All in all a lot of work to save about 75 bucks on having to buy a mid west industries rail, but I like to tinker. Thank you for the kind words. Quote Link to post Share on other sites
rs51085 136 Posted March 11, 2012 Report Share Posted March 11, 2012 just found out that keltec's su-16 series of rifles has a very similar rear peep sight to the tws that comes on there rifle from the factory. you can get the stock plastic peep and the rear sight locks for cheap with free shipping. all together i paid 6 bucks for the set up off of kel-tec cnc website. i haven't received mine yet to verify that it is the correct height. the best part is that if this works out well they also make two other styles of upgrade sights that are the same height, they are made of aluminum and not that expensive. the aluminum model b peep is just 11 dollars and there is also what they call a buck horn sight kit that they sell for $26. i will give an update when i get them to let everyone know how they work out. here is a pic of there buck horn model from there web sight. Quote Link to post Share on other sites
rs51085 136 Posted March 18, 2012 Report Share Posted March 18, 2012 just got the kel tec su - 16 sight and put it on one of my rifles. i think it looks better than the tws peep. this is the polymer model which hardly weighs anything. the aluminum model b is the same design it is just aluminum i think. i haven't tried shooting it yet but i am confident that it will work just fine. 2 Quote Link to post Share on other sites
XXasdf 29 Posted March 18, 2012 Report Share Posted March 18, 2012 Nice pics, I'd like to try out the buckhorn model down the line. I have the TWS factory rear sight right now and I cant really use it with the low mounted red dot I have. Maybe the buckhorn will sit low enough. Quote Link to post Share on other sites
rs51085 136 Posted March 19, 2012 Report Share Posted March 19, 2012 (edited) i just saw the aperture height of the tws peep on css's website and it is .375 from rail. the kel tec sight i got measures .3125 to the center of the aperture with my cheap plastic caliper. that is i believe a 16th of an inch difference. there is way more adjustment than that on the front post so these should work great! xxasdf i don't know if it will be low enough to fix your problem but it will be a little lower that the tws. i am planing on shooting this thing tomorrow so i will report back on how far it is off from factory without adjusting the front site height. Edited March 19, 2012 by rogers 1 Quote Link to post Share on other sites
ShadowFire 220 Posted March 20, 2012 Report Share Posted March 20, 2012 I had to shim my TWS peep sight in place. It would not work as the TWS guy told me it would. I found out why. The gap that the allen bolt goes through, is too wide for the size bolt being used. The best way is to use a larger bolt to keep it from flopping around on the rail. I had to shim the sucker to take up the extra space. Piece of stiff plastic is really all you need to do it, but I still should not have to do it in the first place. I really should send it back. Should rogers report good news, I just might send it back. Rogers, if you have good fortune with it. Please be sure to include how many turns you put on the Front sight and in what direction (clockwise counter clock wise). Quote Link to post Share on other sites
getitat 609 Posted March 20, 2012 Report Share Posted March 20, 2012 Hello XS sights has a "Low Profile Weaver" rear sight listed in their catalog that appears to share similar (approx.) elevation to the TWS unit. It's a peep with integral windage and elevation adjustments, so big plusses there. Haven't found anybody that actually carries them yet, but if I do, I'll probably order one. Respectfully, -guido "God Loves Liberty" Quote Link to post Share on other sites
rs51085 136 Posted March 20, 2012 Report Share Posted March 20, 2012 so the sight worked great. at 35 yards without any adjustment of the front sight it was about 3 inches high and 2 inches to the left. i had to drift the front sight about a 16th of an inch to the charging handle side and and i believe i screwed it out about two turns. i then shot it at 100 yards off hand and they were all on an 8x11 piece of notebook paper.( at least the shots that i didn't wobble on). irons sights at 100 yards are tough! i would recommend getting the model b aluminum version. the polymer version works fine but i think the aluminum version would look better and be tougher. no matter which one you get it will be a lot cheaper than the tws peep and work just as good. Quote Link to post Share on other sites
towerofpower93 22 Posted April 26, 2012 Report Share Posted April 26, 2012 Tag Quote Link to post Share on other sites
JCP281 2 Posted May 5, 2012 Report Share Posted May 5, 2012 Good info on the Kel-tec sights. I thought it was kind of a rip off to charge you 40 bucks for something you need like that... but like mentioned, capitalism lol.. Quote Link to post Share on other sites
waldo18 0 Posted June 12, 2012 Report Share Posted June 12, 2012 so the sight worked great. at 35 yards without any adjustment of the front sight it was about 3 inches high and 2 inches to the left. i had to drift the front sight about a 16th of an inch to the charging handle side and and i believe i screwed it out about two turns. i then shot it at 100 yards off hand and they were all on an 8x11 piece of notebook paper.( at least the shots that i didn't wobble on). irons sights at 100 yards are tough! i would recommend getting the model b aluminum version. the polymer version works fine but i think the aluminum version would look better and be tougher. no matter which one you get it will be a lot cheaper than the tws peep and work just as good. Are the Kel tec aluminum "b"version peep sights adjustable? Quote Link to post Share on other sites
rs51085 136 Posted June 13, 2012 Report Share Posted June 13, 2012 Not sure but I don't think so. I know the plastic a model that I have is not adjustable. Quote Link to post Share on other sites
Squishy 1,149 Posted June 17, 2012 Report Share Posted June 17, 2012 I just ordered the aluminum version, we'll see how she does. Quote Link to post Share on other sites
rs51085 136 Posted June 17, 2012 Report Share Posted June 17, 2012 Can't wait to see it. Quote Link to post Share on other sites
Squishy 1,149 Posted June 17, 2012 Report Share Posted June 17, 2012 Can't wait to see it. I'll post up pics you betcha... Quote Link to post Share on other sites
Squishy 1,149 Posted June 21, 2012 Report Share Posted June 21, 2012 Received the Kel-Tec SU16B-365 rear sight today. Total Price - $24.99 Here are the photos promised. The measurement shown in the last photo was done with a non-digital caliper but it should be close. With the height of this sight the top of the Dog Leg hinge covers roughly the bottom half of the front sight post but the important half is uncovered. As can be seen there are screws on both sides of the sight for windage adjustment. Quote Link to post Share on other sites
rs51085 136 Posted June 23, 2012 Report Share Posted June 23, 2012 That is really awsome that it is adjustable for windage. Let me know how it shoots. Any reason you have it all the way at the front of the cover where the original sight was? I might have to upgrade from my A model. Quote Link to post Share on other sites
Squishy 1,149 Posted June 23, 2012 Report Share Posted June 23, 2012 Any reason you have it all the way at the front of the cover where the original sight was? In effect moving the sight forward zooms in on the front sight. Not really zoom like a zoom lens but it narrows the field of view. With it all the way back you see the whole front sight with some to spare, there's a space all the way around the front circle. With it forward the rear circle is just inside the front circle if this makes any sense. I'll play with it but I imagine as far forward as possible is as close to the original setup as you can get without something in the original leaf location. Quote Link to post Share on other sites
rs51085 136 Posted June 24, 2012 Report Share Posted June 24, 2012 i know what you are saying about seeing less of the front sight to make it more accurate. i made a smaller peep hole on my rear sight by fitting a 3/16" hole plug in the sights hole and drilling a smaller hole in the plug. in effect this did the same thing you are doing by moving the sight further up the rail. have you got to shoot it yet? it should be easy to do since you have the extra wind-age adjustment. let us know how it does. Quote Link to post Share on other sites
saigabob 4 Posted September 24, 2012 Report Share Posted September 24, 2012 any updates from the guys with the kel tec sights? range report? looking at the TWS rail and looking for other rear sight options as well. Anyone running a red dot as well? Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.