-
Content Count
40 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Blogs
Calendar
Store
Everything posted by WingedOne
-
SGAmmo has Lake City M855 Green Tip
WingedOne replied to XD45's topic in General Discussion - Any topic is welcome here!!!
With the " cheap" stuff going for such a high price, you might as well buy something like federal fusion 223. -
I did the washer on hammer pin fix. Works great, had to sand the face of the washer so the fit was tight but didn't bind the hammer. It is now physically impossible for the BHO to clear the rail. Had to do some filling on the safety and slot the BHO to get it all back together. Also make sure your hammer face is center on the firing pin when done.
-
Pull down slightly on the front of the hand guard. Near we're the screw you should have removed is located. Pull the front about an inch from the barrel, then wiggle the ass end out. Don't touch your "gas holes" until you master hand guard removal. You'll go blind.
-
Realistic HD Weapon
WingedOne replied to TO THE FLOOR IN A 63's topic in General Discussion - Any topic is welcome here!!!
I make rounds every night to make sure all doors and windows are locked. Then check that my firearms and flashlight are where I can find them in a dead sleep. -
If you have a retaining plate make sure it isn't dragging on the carrier. I had to shave a bit off the top near where the safety passes through. Don't know if it applies to you but?
-
Gave the brush on a drill a shot, seemed to help. No longer catches fibers from a patch when I pass it through. I will put some slugs down range next time I'm out. Thanks for the advice.
-
I put 100 rounds of bulk pack and 15 of buck through her. Think I need something more abrasive than plastic wad. Maybe some 600 grit on the end of a dowel?
-
I just got done enlarging a three port Saiga to 3/32. Gun cycles great frm the hip now with federal bulk pack, kicking shells out a good three feet. They used to just kind of fall out before the mod. The problem I'm having is pieces of the wad are being sliced off and making their way into the gas block. Correct angle of ports was kept. I think there is a sharp edge in the barrel. Does any one have any good ideas to deburr the ports?
-
Where's Mike "Contest"
WingedOne replied to cvhanh20's topic in General Discussion - Any topic is welcome here!!!
I think Cameron knows something we don't. -
married 20 years tomorrow
WingedOne replied to sparky63's topic in General Discussion - Any topic is welcome here!!!
Tim you were the only one who got the Atlas Shruged reference. Now you tell me you got your wife a pallet of scratch and dent tampons for an anniversary gift. Damnit man. I don't know if I should laugh or cry. Good on ya though I'd be sleeping on the couch. -
Agreed the shells will deform if they are being smashed by spring pressure against the closed bolt. Leave the bolt locked back and I don't foresee any problems, that's my plan for what it's worth. Besides the internets told me the sound of a 12 gauge being racked will make the bad guys quit their evil ways and reach for the heavens. reach for the heavens.
-
Yet another benefit of having Count Chocula for breakfast, it's safer. Deadeye, actually that's exactly what I'm thinking of doing although the hole saw I have on the way is 5/8" which is 1/16" smaller and, a size that is readily available. The one I'm getting is a fine tooth, 10TPI so hopefully it won't tear things up too badly. But if it does I'm going to remove the teeth and sharpen the edge. I actually found a "knife edge" hole saw but because they're made out of spring steel they couldn't be made this small. Would you have a link to the vid? Count chocula is made of cardboa
-
Does anyone else watch videos of people shooting bird shot into corn fields and hope there corn flakes didn't come from that field? Or is that just me? Same with shooting into water supplies.
-
6500's talk of balance is what interest me in a bullpup S12. Try it, take the stock off and shoulder it, now that's some damn nice balance. Now what happens when you fire it without all that weight on the muzzle ????
-
Internal receiver block with a pignose adapter from CSS and your favorite AR stock and buffertube. Not comm Block but the pignose has about an inch of adjustment built in.
-
Where can I find one?
-
I have an 08 three port gun that ate this same ammo up for breakin. The only thing I did prehand was lube her up well and rack the slide a few hundered times. That is high brass ammo and not to be confused with the Winchester Super Speed Xtra.